Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
FDL310
|
Tu board different than found in the s/m, correction issued | Tu board is different from the one in the service manual.also q-402 is a smaller type with x7 stamped on it. need the correctschematic and part number for q-402. -hq comments: q-402 was changed to 2sd1048x7 its part number is8-729-800-78, which as be | ||
| SONY |
XRU330
|
Unable to correctly insert front panel section | Unable to correctly insert front panel section as per manual. | ||
| SONY |
SPPA60
|
Part number availability for battery sponge | In the service manual there is no part number supplied for thebattery sponge that is attached to the handset rear cover. | ||
| SONY |
SPPA40
|
Part number availability for battery sponge | In the service manual there is no part number supplied for thebattery sponge that is attached to the handset rear cover. | ||
| SONY |
CDPC225
|
Intermittently will not turn on | Unit intermittently will not power up. | ||
| SONY |
KP5040
|
Inoperative set - no relay click, replaced q-654 (ga board) | Inoperative set with no relay click. found no +12v dc at plugga-13 pin no. 3. found q-654 open emitter to base. | ||
| SONY |
CCDV5000
|
New audio/pcm pc board version incompatibility/sm supp-1 | Instead of pc-35, we found a different version pc-52, withcustomer complaint as huming noise as in manual mode, even with and levelcontrol at minimum setting (0) level. the circuit is different withpc-35. replaced with pc-35 that solved the hum. all a | ||
| SONY |
HCDH50
|
Unit stuck on 9khz spacing | Unit is stuck on 9 khz spacing on a.m. how do you change from9 khz to 10 khz spacing? | ||
| SONY |
HCDH1600
|
Substitute ic-205 requires circuit changes - d-101 fails | Kcp automatically subs this chip to a cxa1492aq, part number8-759-058-95. when you install the new device, d-201 fails and the newchip may fail also. | ||
| SONY |
FDL3500
|
Max and mim current, 2-3 ma mim, 500ma max | Customer complaining about short battery life. the servicemanual does not supply the minimum current drain when the set is in theoff position. can you supply? -hq comments:tv mode: 500maam/fm mode: 60maoff: 2-3ma | ||
| SONY |
MZ1
|
Restoring unusable m/o discs to usable condition | The display shows utoc error when trying to read an m/odisc. this problem may have been caused by the customer moving the unitwhile it was updating the utoc area after recording. the owner's manualindicates that the disc must be replaced. | ||
| SONY |
CCDTR5
|
Service bulletin number cam0171 - original screws too short | When performing service bulletin no. cam0171, and installingthe new base block assembly the original mounting screws are now tooshort. | ||
| SONY |
XRU770
|
Amp remote stays on with power off | Customer states that power amp stays on even when unit is off. | ||
| SONY |
CCDTR81
|
Intermittent play - shutdown in rewind/relay belt ref 367 | Unit would play for a short time and shutdown. shutdown inrewind occasionally eats tapes. | ||
| SONY |
CCDTR1000
|
Owner's manual for ccd-tr1000/same as ccd-tr101 | |||
| SONY |
CCDTR101
|
Unit will not edit search/defective switch block | Edit + and - both would cause tape to roll. however, videowould be muted. suspect faulty matrix. | ||
| SONY |
CCDV801
|
Circuit boards are different/sm supp-2 | |||
| SONY |
HSTV102
|
Need motor mount part number | Part number for motor mount shown on page 28, shown as notsupplied. part got thrown out with old motor. -hq comments: we have contacted tokyo and they have agreed to send onepiece for the repair of this unit. we will inform you once we receive it.4/22 | ||
| SONY |
KV32XBR15
|
Bad pincushion, q-505 gets hot, replaced l501 | Servicer had problem with pincushion. replaced r-571, q-505and d-512. checked l-501 and thought it was ok. it read about 2Ω andit should be approximately 4.5Ω. i suggest a service bulletin beissued concerning the above. -hq comments: please | ||
| SONY |
PVM1271Q
|
Picture had severe pincushion | Monitor had a severe pincushion problem and was expandedhorizontally. pin and horizontal controls had no effect. traced problemto pincushion transistor q-806. voltage at the collector of q806 was 3.4volts, not 35.1 volts as stated in the service manua |