Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
SONY |
HSTV102
|
Need motor mount part number | Part number for motor mount shown on page 28, shown as notsupplied. part got thrown out with old motor. -hq comments: we have contacted tokyo and they have agreed to send onepiece for the repair of this unit. we will inform you once we receive it.4/22 | ||
SONY |
KV32XBR15
|
Bad pincushion, q-505 gets hot, replaced l501 | Servicer had problem with pincushion. replaced r-571, q-505and d-512. checked l-501 and thought it was ok. it read about 2Ω andit should be approximately 4.5Ω. i suggest a service bulletin beissued concerning the above. -hq comments: please | ||
SONY |
PVM1271Q
|
Picture had severe pincushion | Monitor had a severe pincushion problem and was expandedhorizontally. pin and horizontal controls had no effect. traced problemto pincushion transistor q-806. voltage at the collector of q806 was 3.4volts, not 35.1 volts as stated in the service manua | ||
SONY |
CDPC325
|
Intermittently will not turn on | Unit intermittently will not power up. | ||
SONY |
CCDFX511
|
Part number for mode select switch | What is the part number for the mode select switch? -hq comments: part number is 1-572-986-11. | ||
SONY |
CCDFX510
|
Part number for mode select switch | What is the part number for the mode select switch? -hq comments: part number is 1-572-986-11. | ||
SONY |
CCDFX411
|
Part number for mode select switch | What is the part number for the mode select switch? -hq comments: part number is 1-572-986-11. | ||
SONY |
CCDFX410
|
Part number for mode select switch | What is the part number for the mode select switch? -hq comments: part number is 1-572-986-11. | ||
SONY |
CCDFX310
|
Part number for mode select switch | What is the part number for the mode select switch? -hq comments: part number is 1-572-986-11. | ||
SONY |
GEN-HFP
|
Tips on removing 94 pin flat pack ic's or larger | Removing 94 pin flat pack ics or larger. example: ic-701tadm1000es do not have the right hozan tip to fit. | ||
SONY |
TADM1000ES
|
No sircs output on video one - ic701 (p/n 8-759-152-23) | No sircs output to video one or video two but other sircsoutputs are fine. | ||
SONY |
KV32XBR35
|
Pip picture is breaking up, replaced p-1 board. | Picture in picture would break up vertically. | ||
SONY |
KPR41EXR95
|
Center speaker connections, see tv service bulletin 149 | Customer had professional installation of unit but could notget center channel to function. found terminal connections on ut boardto be strangely configured. | ||
SONY |
EVA50
|
Intermittently eats tape | Contacts in connector not making contact. | ||
SONY |
EVC40
|
Intermittently eats tape | Spring contacts in connector were not contacting. | ||
SONY |
CCDTR101
|
Image stabilizer inoperative | Found flex unsoldered at w-101. | ||
SONY |
SPPA60
|
No battery back-up | Unit has no battery back-up. power led always flashes. foundtwo different problems, ref. no. 25 and/or ref. nos. 18/19 are missing onseveral units. also, found that ref. no. 19 is bent on several units,making bad contact to main board. also applies t | ||
SONY |
ITA205
|
No answer machine function | Unit was unable to do any answer machine function (ff, rew,play, ogm). checked vcc and reset. both were correct. checked forcrystal (x-601) at pin 24 and pin 25 of ic-602 and found no frequency.found x-601 open. | ||
SONY |
SPPA20
|
No power handset | X-502 was oscillating at the right frequency but theamplitude of the signal was insufficient to operate the micro. thedefective crystal amplitude was down 50 percent. | ||
SONY |
SPP57
|
No ring | Unit would page but would not ring from external line. tracedproblem to defective r-72. |