Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV32XBR95S
|
No picture in tv mode, resoldered both q-605, and d-655 | No picture in tv mode, the video mode was ok but missing two inches at the bottom of screen. found all b+ voltages low causing incorrect voltage at tuner and vertical. | ||
| SONY |
DTC670
|
Unit won't completely rewind | Unit would play and fast forward correctly, but wouldn'tcompletely rewind a dt120 tape. all play tensions were correct. however,with no tape loaded and mechanism in rewind, turning take-up spindle withfingers revealed high stiffness and drag. | ||
| SONY |
HCDH1500
|
Inoperative unit | Unit is inoperative. start up power supplies and fuses on power supply pcb all are good. no red led for standby. | ||
| SONY |
TCW31
|
"b" deck has no playback | B deck has no playback. ic-303 is not switched from a tob deck. | ||
| SONY |
KV20EXR20
|
High pitched sound, replaced c-507 | High pitched sound gets louder after two hours. used the radioshack sound level meter with an extension tube connected to its input.this allowed pinpointing of the part. | ||
| SONY |
KV20TS27
|
No sound, replaced ic101 | No sound. | ||
| SONY |
STRD990
|
Unit cycles off immediately when powered up | Unit immediateley shuts off when powered up. fuses were allfine. | ||
| SONY |
TRWR670
|
After unit heats up, head assembly jumps erratically, ic802 | After unit warms up, heads continue to jump erratically. | ||
| SONY |
SEQ711
|
Could not select between tape and line functions | Unit only worked through line inputs. it could not switch totape mode. | ||
| SONY |
TADL100
|
No audio/communication is ok | No audio out of decoder board. efm is ok. found cold solder joint on x-201 and case ground shield. | ||
| SONY |
CFD757
|
Distorted audio above level 5 - l-308 (open) | Audio distorts above level 5. sounded like feedback. i couldsee on scope distortion at selector ic. finally disconnected mic amp icand distortion won't go away. Ωed out mix mic jack and found it not tobe grounded through l-308 which was open. | ||
| SONY |
TADL100
|
Distorted audio | Audio distorted, signal clipped. | ||
| SONY |
CFD460
|
Cd plays intermittently | Cd would play intermittently. q-706 junctions checked ok with anΩmeter. | ||
| SONY |
STRD790
|
No display and unit works | Checked ac voltage and +30 volt lines to display and both weregood. replaced fl-101 without resolving problem. traced the fl clock andfl data to system control ic-202 pins 18 and 19. found below standardsoldering on this ic. | ||
| SONY |
KV27EXR15
|
Picture gets dark intermittently, resoldered r-739 | Picture gets very dark intermittently. it shows color only. | ||
| SONY |
CCDFX410
|
Unit chatters when fully loaded/unloaded | Using the mode box when unloading stop and fwd lights wouldkeep repeating. | ||
| SONY |
STRAV1070X
|
Erratic symptoms | Servicer has four units with the following symptoms:1. remote may not work. 2. on and off by itself. 3. e is on display.4. no display. 5. surround and drlc relays on and off by themselves. 6.cannot turn unit off. procedure from service bulletin no. | ||
| SONY |
KV20EXR20
|
Loud mechanism hum, glued shield (t-602) | Metal shield around t-602 is loose, causing mechanical 60hzhum or buzz. have seen this on sevreal other units also. | ||
| SONY |
CDXA55
|
Part number correction: connector flexible board (ref. 102) | This flex cable does not fit in unit. this part # shows upin the system for model cdx-u300. the part number taken from the flexconnector of the cdx-a55 is 1-643-777-11, which substitutes to1-646-391-11. | ||
| SONY |
SPPA60
|
Handset transmit frequency is low | X-501 is defective preventing ic-501 (pll) from operatingproperly. x-501 is producting a low amplitude which is not sufficient tocorrectly run ic-501 (pll). this also prevents the tx frequency frombeing adjusted to the correct frequency. also applies |