Sony Repair Tips
Search: sony
Results: 20077
Results: 20077
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CFD455
|
Idler assembly wears out after four to six months of use | This part is highly consumed. part is failing prematurelyeven after just a small amount of use. -hq comments: also applies to model cfd-750/760.tokyo has been informed. your samples have been sent to tokyo forevaluation. tokyo has evaluated the sampl | ||
| SONY |
KPR46XBR15
|
Service manual correction (st vco adjustment) | St vco adjustment (page 67) step no. 7 does not say what toset stev data to. | ||
| SONY |
KV27HSR10
|
Black band across top of screen lines in video, fpr n2744 | This was a new twist to the bad regulator solder joints.screen had lines across it, pulled down, and retrace lines. resolderedthe three regulators and hdt readjusted h frequency, vertical height andposition, reset system/mircoprocessor. | ||
| SONY |
KV1222R
|
No functions from remote or controls, replaced ic-001 | No functions from front panel or remote. | ||
| SONY |
TCWR670
|
No ams | No ams. traced audio out from ams circuit to pin 5 of ic-801(ams in) and all the other functions worked. | ||
| SONY |
FD510
|
No video, solder bridge between ic-201/pin 14 & c-406 | No video. found solder hair between ic-201/pin 14 and the ground side of c-406. | ||
| SONY |
CCDTR1
|
Bad head | Looks like bad head. checked pin 14 of ic-102 had b headrf, checked pin 12 same ic had no rf. | ||
| SONY |
BMC550
|
Immediate shutdown - rv-201 | Unit shuts down immediately after pressing record. found badspot on drum speed adjustment pot. | ||
| SONY |
CDPH1750
|
Does not read discs | Unit spins disc and servos appear to be working but displayreads no disc. found small holes in traces. this is the second onei've received like this. | ||
| SONY |
KV27XBR95S
|
Ticking sound when channel change, normal | San diego ssc home technician informed me of a problem that heis unable to resolve. when channel up/down is used the set produces aticking sound (not popping) through the speakers. -hq commets: we have a 32xbr95s in our lab. when changing channelsthere | ||
| SONY |
KV27EXR90
|
Video adjustments don't work, check asc circuit | Color, hue, sharpness, brightness, picture: display barchanges but picture does not change. when power turned off, then back on,then picture changes. all else seems ok. true with asc on or off.ic-101, ic-102, ic-104, ic-301 have been changed. asc boa | ||
| SONY |
SPPD15
|
No audio | Handset locked in with the base but there was no audio fromhandset speaker. put the handset in test mode and got static so i decidedto go to the base. after measuring ic3/ pin 2, i found that ic3/pins 2 and3 were not equal and ic3/pin 1 had no voltage. | ||
| SONY |
CDX5180
|
No audio, then no cd operation after replacing ic-701 | Unit had no audio and would not read toc on disc. | ||
| SONY |
CCDFX710
|
Blows fuses f-950 | Unit would blow fuse f-950 when assembled and all cabinetscrews were tight. found viewfinder 5 volt line to have frayedinsulation. when screws were tightened on, right case component wouldflow through rotating viewfinder bracket through f-011 sticker t | ||
| SONY |
SPP190
|
No charge | Charge led was not coming on. measured charge terminal.there was output voltage but no ground to negative terminal through q-609.replaced q-609, unit was ok. | ||
| SONY |
HCDD117
|
Cd door doesn't open/close; sled doesn't move | Cd door will not open or close nor will sled operate. thereis +7v present at cn-101 but not at ic-103 or ic-102. | ||
| SONY |
KV32XBR95S
|
Intermittent color, resoldered ic-1204 | Color would fade to black and white after turn on. | ||
| SONY |
CCDFX410
|
Ccd-fx series viewfinders/ccd-fx620 s/m | |||
| SONY |
FD510
|
Audio goes to full volume intermittently, resoldered cn-601 | Audio goes to full volume. traced to intermittent groundwire on volume pot. replace wire cn-601/pin 6. | ||
| SONY |
FD510
|
Hum in audio, change value of c-601 to 4700uf | Hum in audio specially in tv mode. on the new chassis wehave this problem but not on the fd-500. i reviewed the two manuals andfound the difference between the two power supplies, was the value of thefilter capacitor. in the fd-500, c-600 is a 4700uf |