Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CCDF55
|
No video from camera | No video from camera. | ||
| SONY |
KV32XBR70
|
Dead, replace q-505, q-503 and r-571 | The pcb and the pictorial have the legs of q-505 mislabeled.i believe reverse the base and emitter for proper installation. even whenq-505 is on heat sink, it can be reversed. on this set, q-505 was shortedalong with q-503 and r-571. replacement did n | ||
| SONY |
KPR46CX10
|
Vertical sweep collapse, replaced q-403, 404, and 405 | Failure caused crt permanent damage (red crt). | ||
| SONY |
D25
|
Audio mutes and display goes blank intermittently | Unit is intermittent and acts as though it was tapped veryhard. sound mutes and time display goes away and comes back at the samepoint on the disc - no skipping. the spring becomes weak and the opticalblock cannot move forward because of the pressure o | ||
| SONY |
D15
|
Audio mutes and display goes blank intermittently | Unit is intermittent and acts as though it was tapped veryhard. sound mutes and time display goes away and comes back at the samepoint on the disc - no skipping. the spring becomes weak and the opticalblock cannot move forward because of the pressure o | ||
| SONY |
KV27HSR10
|
Dead, replaced fbt, r-571 and q-505 | The unit came in with a shorted hdt. a new replacement wasimmediately burnt out. | ||
| SONY |
CFDW888
|
Unit skips intermittently | New optic and old one have flex lead rubbing against bottom of chassis plate. this causes skipping when sled motor moves. -hq comments: thanks for the info. tokyo has been informed. | ||
| SONY |
KV19TS20
|
Picture drifts, replace q-112 | Picture drifts and distorts. | ||
| SONY |
KV27TS20
|
Pincushion distortion, d519 | Pincushion distortion. | ||
| SONY |
SPPS10
|
No audio on handset | Handset audio board separates from the main circuit boardpulling the connection loose from the (audio) board. the audio board isnot available as a part, the entire main circuit board must be replaced. | ||
| SONY |
DTC700
|
No display | Unit had no -24 volts on cn-791. | ||
| SONY |
KPR46CX10
|
On/off button part number, must change front bezel | Need the part number for the on/off button. this button comesas part of the bezel. it is very expensive to the customer to have toreplace the whole bezel just for one button. -hq comments: the buttons are not available nor, will they be made as arepl | ||
| SONY |
TCWR11ES
|
Service manual does not exist | Need part number for wood side panels, but there is no servicemanual. -hq comments: use the service manual for the tcwr950, as it is virtuallyidentical to the tcwr11es. a one-page manual for the tcwr11es describesthe differences between it and the tcwr | ||
| SONY |
KV32XBR10
|
Bad solder joints around t-501 hdt, resoldered t-501 | Bad solder joint around t-501 hdt and unit had a bad h-outd-1941. | ||
| SONY |
KV32XBR15
|
No pix, or sound, cold solder joint on t-501 hdt, | Bad solder around t-501 hdt, caused the loss of hor sweep andno raster resulted | ||
| SONY |
TAM50
|
Intermittently machine stops | Intermittently machine will not reset or sometimes stops inmiddle of icm recording. at that time you will see (-) on display. alsopertains to serial number 23638. | ||
| SONY |
ITA850
|
No sound | Machine will automatically switch from ogm-a to ogm-b afterfirst icm was recording. headwire (hrp-701) is shorted (machine actinglike icm tape is full) caused by ic-211 not in right position and touchingthe headwire. thereby, shorting out the wire. | ||
| SONY |
CDXA2001
|
Discs jamming in the xa-10b | Have received numerous complaints of discs jamming in xa-10b.problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in xa-10b). themost common brand of discs with this problem is | ||
| SONY |
CDXA30
|
Discs jamming in the xa-10b | Have received numerous complaints of discs jamming in xa-10b.problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in xa-10b). themost common brand of discs with this problem is | ||
| SONY |
CDXA20
|
Discs jamming in the xa-10b | Have received numerous complaints of discs jamming in xa-10b.problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in xa-10b). themost common brand of discs with this problem is |