☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY RME300
Part number for the control "l" cable 3 pin to 3 pin What is the part number for the three pin to three pin controll cable in the rme-300?
SONY CDP670
Abnormal tracking When trying to advance to the last track of the yeds 18 disc(track 22), the laser would advance to the outer edge, the disc would stopspinning, the laser would go back to the limit switch and then advance totrack 22 and play.
SONY CCDF55
Tech tip for servicing with mode selector iii When working on ccd-f55s, there is no way to hook up the load-ing motor to the mode selector. technical department is researching aboutgetting a connector which could hook two cables to the mode selector.
SONY CFSW30
Incorrect part number for spring - reference no. 12 The part number for reference no. 12 of exploded view on page21 of service manual is incorrect.
SONY CFSD30
Wrong part number listed in s/m for vr-101 This part is the bank of slide pots for the eq and the volume.when this part is ordered, the part received is a 2-gang rotary pot. thepart received is the balance control for a tc-wr510. please providecorrect p/n. -hq comments: tokyo fax a910094: p/n
SONY SLHF750
Unit does not thread/unthread tape Unit would not thread/unthread tape by supplying external dcvoltage to threading motor. relay gear assembly would slip and chatter.noticed that the shaft on which this gear assembly mounts on was pushedupwards and didn't enter the hole designated for it
SONY SLV272UC
Dead Power light comes on for approximately 15 seconds then shutsdown. no switched 12v and 13 volts from pins 7 and 9 of ic-501 regulator.
SONY SCD1020S
No audio alarm/buzzer from keyboard- no beeps Audio buzzer not functioning from keyboard - no beeps.
SONY SCD1020S
Keyboard dead or will not take key input Keyboard dead. will not react to any key input.
SONY SCD1020S
Loopback test stops automatically after 1 transmission While in service mode and running a loopback test (tx/rxtest), the test will automatically stop after sending only 1 transmission(3 min).
SONY SCD1020S
No receive/sna does turn off/no error codes The keyboard's satellite not available led will turn offwhich means the receiver is locked and able to receive.however, the system will not receive any message even though sna led isoff and system is currently in service. no error codes are displayed.
SONY SCD1020S
Keyboard loses power/display when bumped When keyboard is bumped or exposed to vibration, the unitloses power/display and will restart itself back to self-diagnostics (start up routine). this is being caused by an intermittentconnection in the prom socket. this is due the nature of a lock in
SONY SCD1020S
Keyboard will not function The keyboard keys will not function. unable to input specifickeys that stick.
SONY SCD1020S
System is stuck in "self-diagnostics" screen Upon powering system up, the keyboard normally displays self-diagnostics. after completion of self-diagnostics, the keyboard willdisplay the transmit menu. on these units, the system did not allow exitfrom the self-diagnostics screen and was stuck in t
SONY CCDTR5
Intermittent loading and eject Unit would not always eject and load properly.
SONY TCWR808M
Cassette deck - no operation Reset pin of ic-401 was never going high to 5 volts. thisline was followed back to q-402 and q-401 which were measured with a dvm.q-402 base was .1vdc, however, q-402 appeared to be on. measuring thebase of q-402 with an oscilloscope showed approximate
SONY E92F19B160
No part number listed for front panel - reference no. 101 There is no part number listed on page 35 of the s/m for thefront panel (ref. no. 101). -hq comments: from w. janowski/c. rashi (detroit ssc): p/n is1-464-753-11. this part includes the panel, all the buttons, and thedisplay pcb. although it seems as i
SONY SCD1020S
Missing part number on receiver cable Both tx and rx antenna cables at antenna end have a protectiveboot that covers the end connector. when these cables are supplied withproduct, there is no problem. however, when supplied thru npc parts,there is a missing retainer ring on the rx cable.
SONY KV27TS20
Sap not working, alignment? I was contacted by a customer because sap didn't work on hisunit (we have weather on channel 6, the pbs channel here). he went to thestore and the display model didn't work either. i went to another storeand the display didn't work on sap either. -hq
SONY CDX6020
Will not load disc - roller slipping on shaft The disc will not be pulled into the unit. it may also not beejected. the disc is engaged with the roller, but the roller is slippingon the shaft.