Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV19TS20
|
Picture drifts, replace q-112 | Picture drifts and distorts. | ||
| SONY |
KV27TS20
|
Pincushion distortion, d519 | Pincushion distortion. | ||
| SONY |
SPPS10
|
No audio on handset | Handset audio board separates from the main circuit boardpulling the connection loose from the (audio) board. the audio board isnot available as a part, the entire main circuit board must be replaced. | ||
| SONY |
DTC700
|
No display | Unit had no -24 volts on cn-791. | ||
| SONY |
KPR46CX10
|
On/off button part number, must change front bezel | Need the part number for the on/off button. this button comesas part of the bezel. it is very expensive to the customer to have toreplace the whole bezel just for one button. -hq comments: the buttons are not available nor, will they be made as arepl | ||
| SONY |
TCWR11ES
|
Service manual does not exist | Need part number for wood side panels, but there is no servicemanual. -hq comments: use the service manual for the tcwr950, as it is virtuallyidentical to the tcwr11es. a one-page manual for the tcwr11es describesthe differences between it and the tcwr | ||
| SONY |
KV32XBR10
|
Bad solder joints around t-501 hdt, resoldered t-501 | Bad solder joint around t-501 hdt and unit had a bad h-outd-1941. | ||
| SONY |
KV32XBR15
|
No pix, or sound, cold solder joint on t-501 hdt, | Bad solder around t-501 hdt, caused the loss of hor sweep andno raster resulted | ||
| SONY |
TAM50
|
Intermittently machine stops | Intermittently machine will not reset or sometimes stops inmiddle of icm recording. at that time you will see (-) on display. alsopertains to serial number 23638. | ||
| SONY |
ITA850
|
No sound | Machine will automatically switch from ogm-a to ogm-b afterfirst icm was recording. headwire (hrp-701) is shorted (machine actinglike icm tape is full) caused by ic-211 not in right position and touchingthe headwire. thereby, shorting out the wire. | ||
| SONY |
CDXA2001
|
Discs jamming in the xa-10b | Have received numerous complaints of discs jamming in xa-10b.problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in xa-10b). themost common brand of discs with this problem is | ||
| SONY |
CDXA30
|
Discs jamming in the xa-10b | Have received numerous complaints of discs jamming in xa-10b.problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in xa-10b). themost common brand of discs with this problem is | ||
| SONY |
CDXA20
|
Discs jamming in the xa-10b | Have received numerous complaints of discs jamming in xa-10b.problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in xa-10b). themost common brand of discs with this problem is | ||
| SONY |
CCDF56
|
No playback - audio | Unit would not playback any audio. | ||
| SONY |
CCDV9
|
New track shift jig subs to the old part number | A servicer tried to order the new track shift jig and itsubstitutes to the old part number (j6080843a). how can i get the newtrack shift jig? -hq comments: i checked both of the part numbers and they are bothgood in kcp. | ||
| SONY |
SLV555UC
|
Adjustment of switching position 2 | When attempting to make the switching position adjustment 2 asfound on page 140 of the service manual, i was unable to make any changeto the switching position by adjusting rv-501 on the ma-34 board. | ||
| SONY |
SLV555UC
|
Slow rewind - unit shuts down | When rewinding tape, especially near the beginning of the tapethe tape would slow down excessively and at times the unit would shutdown. play mode was normal. | ||
| SONY |
STRAV480
|
Audio output ic-701 keeps failing | Ic-701 fails (audio output ic). sometimes afterreplacing, ic-701 unit would work for a long time before going intoprotect mode because ic-701 had shorted out. other times it would shutdown almost instantly. again i would find ic-701 had shorted out (d | ||
| SONY |
CDPC900
|
Discs jamming in magazine | Disc gets jammed in unit. removed and realigned - checkedoperation of unit. transport appears all ok. after a week to 10 days,unit comes back with same problem. | ||
| SONY |
CDXA10
|
Discs jamming in the xa-10b | Have received numerous complaints of discs jamming in xa-10b.problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in xa-10b). themost common brand of discs with this problem is |