Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
KV1513
|
Shutdown | After 10 minutes, set would cut off. channel numbers remainedlit. | ||
| SONY |
WMF100II
|
Schematic correction | Part 3-329-713-01, holder (left), cassette and 3-329-714-01,holder (right), cassette are switched in the exploded view schematic. -hq comments: thanks for the info. we will advise tokyo.to tokyo: this is for your information. | ||
| SONY |
S3900
|
Cassette deck not accessed via remote | The remote control does not access the cassette deck(tcw295). sales literature indicates that it would. | ||
| SONY |
KV27XBR10
|
Horizontal off freq, hue shifted to green, replaced ic-301 | Horizontal was locked with blanking bar six inches from right.also color was green. adjustment would not bring into correct position. | ||
| SONY |
PVM2530
|
Part number missing for cp components | Need part numbers for all cp packs on (11-a) board. also needpart number for d-2325 which is shown on the actual pc board but not onthe schematic or board diagram. -hq comments: please refer to service manual correction no. 4. | ||
| SONY |
CDXR66
|
Incompatibility of new md sled chassis and old chuck plate | When you order x-3320-567-1 md sled chassis assembly, itsubstitutes to x-3320-567-2. when installed, unit will not clampcorrectly. i found when ordering chuck plate (5) (ref. no.261) itsubstitutes to new part number 3-348-558-01. it will clamp correct | ||
| SONY |
CDXR88
|
Incompatibility of new md sled chassis and old chuck plate | When you order x-3320-567-1 md sled chassis assembly, itsubstitutes to x-3320-567-2. when installed, unit will not clampcorrectly. i found when ordering chuck plate (5) (ref. no.261) itsubstitutes to new part number 3-348-558-01. it will clamp correct | ||
| SONY |
CDXR77
|
Part number missing | Original service manual shows c-701 as (1-163-059-00).01uf 50v chip capacitor on page 47. the schematic shows that it is a.22f 5.5v capacitor. investigation revealed that the part number forc-701 should be 1-125-486-11. | ||
| SONY |
CDP370
|
Cdp-370 will not play or load | Cdp-370 would load but would not play. then the drawer wouldopen but would not close when open/close button was pushed. i also founda voltage discrepancy on ic-6, pin 50. the manual says it should be 8volts but is is 22 volts. | ||
| SONY |
TCWR710
|
Deck (a) no function | Unit would not go into play. pressing play would cause unitto go into fast forward, rewind or nothing at all. | ||
| SONY |
WMF100III
|
Incorrect shipment of parts | When you order reference number 109 (p/n 3-329-737-01), youget reference number 133 (p/n 3-329-736-01). are the part numbersreversed in the service manual or has the stock been mixed up? -hq comments: i checked with kansas city parts on this and they f | ||
| SONY |
WMF100II
|
Incorrect shipment of parts | When you order reference number 75 (p/n 3-329-736-01), you getreference number 84 (p/n 3-329-737-01). are the part numbers reversed inthe service manual or has the stock been mixed up? -hq comments: thanks for sending this information to us. | ||
| SONY |
STJX380
|
Will not hold channels in memory or lock on to a channel | This tuner would not hold channels in memory or lock on to achannel. | ||
| SONY |
GEN-VID
|
Tape skew around ace assembly | Capstan wears causing tape skew around the ace assembly. i was wondering if it was possible to get just the capstan instead of the whole motor in hopes of making units more economical to repair? | ||
| SONY |
D9
|
Spins but will not read toc | There is a black plastic and copper shield glued to the top ofthe processing ics on the main board. noticed that the ground connectionwas missing. added jumper to ground and checked ok. apparently, theungrounded shield was acting more like an antenna. | ||
| SONY |
CDPC10
|
No reset button | On page 5 of the service manual, in both the laser checkprocedure and the troubleshooting flow chart, there is mention of a resetbutton, while none exists in the unit. -hq comments: thanks for the info. there is no reset button as younoted. to reset t | ||
| SONY |
XR6500
|
Rew/ff knob falls off | I have had three customers call that have this unit that com-plain that the ff/rew knob comes off when they pull it to perform ff/rew. | ||
| SONY |
CDP701ES
|
Apc adjustment procedure | The attached fpr from 10/23/85 (not in computer) indicatesthat it would be issued on how to adjust the laser output but i cannotfind any such service bulletin or supplement etc. was this ever issued?what is the adjustment procedure? -hq comments: when | ||
| SONY |
TAAX520
|
Right channel out | When the bass control is turned up, the right channel will cutout. | ||
| SONY |
EVC3
|
No power and does not work | No power and does not work. |