Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
SONY |
TCWR510
|
Pause light operation | When should the pause indicator operate? does it operateonly with the remote or should it operate anytime? -hp comments: the pause indicator will only be on when the pausefunction is activated using the remote. the pause button on the frontpanel will | ||
SONY |
KV2728R
|
Picture unstable horizontally, replace c-1537 on d board | Problem looked like poor horizontal afc lock. slight fold-over on left side and picture would shift from right side to left side.it looked like unstable horizontal sync. | ||
SONY |
SLV70HF
|
Loads, unloads then shuts down. eject only works. | When play is pressed unit loads, unloads and shuts down.it will only eject after this. also the vtr switch will switch offthereby returning to tv operation. | ||
SONY |
WMF701C
|
Broken post for reel spindle | The post for the reel spindles (ref. # 318 and 321) breakoff from the chassis (ref. # 353). the post is attached to the chassisby slightly flaring the bottom of the post. in the cases i haveseen, the post simply pulled through the hole. -hq comments: | ||
SONY |
KV27XBR10
|
4 inch blanking bar on right side, replaced ic-301 | Unit comes in with the blinking bar about four inches on right side of screen. | ||
SONY |
SLHF860D
|
Will not playback or record | Unit will accept tapes, load, threads and you can rewind orffw. if you hit (play) or record, there is no movement and no buttonswill work even power on/off. you have to unplug the unit to eject thetapes again. | ||
SONY |
DT3
|
Laser stays on continuously | Ic-501 (cxa-1081q) has ld on (pin 10) permanently tied low.this pin normally controls the laser on output from the ic. if pin 10 islow, the laser is on. does this mean the laser is always on in this unit? -hq comments: not exactly. the power supply t | ||
SONY |
D3
|
Laser stays on continuously | Ic-501 (cxa-1081q) has ld on (pin 10) permanently tied low.this pin normally controls the laser on output from the ic. if pin 10 islow, the laser is on. does this mean the laser is always on in this unit? -hq comments: not exactly. the power supply t | ||
SONY |
CFS4000
|
Replacement counter belt does not fit | Replacement counter belt is too large by about 1cm. the beltis replaced by part number 3-642-544-xx. please advise us as to anotherpart number. -hq comments: the counter belt, ref. 359, part number 3-434-110-xx isreplaced by part number 3-657-035-xx. | ||
SONY |
KV27XBR10
|
Distorted audio in srs mode, replaced srs module, sb 45r1 | Audio was distorted in one channel when in the srs mode. | ||
SONY |
KPR36XBR
|
Ripple in picture, replaced ic-5007 | The asc reports that this set experienced the normal failureof the coil and diode on the e board and after they were replaced thepicture had a ripple going down the side. the trouble was ic5007on the e board - replaced it and pix was ok. we have not be | ||
SONY |
KV32XBR10
|
Woo-woo sound, replaced srs module, s/b 045r1 | Verified problem in customers home. hum comes and goes,especially with male voice, on real stereo broadcasts with srs turned on. | ||
SONY |
KV27XBR15
|
Woo-woo sound srs mode, replaced srs module see tvp sb #45r1 | Hum comes and goes especially with male voice on real stereobroadcasts with srs turned on. | ||
SONY |
CDP270
|
D.o.a. - will not spin disc | Fok, sens, mon, mds, mdp are all normal. no action at ic-3/pin 45 spdlo. pull up ic-5/ pin 2 to 5v through 1k resistor causesspindle motor to turn. | ||
SONY |
CCDTR5
|
Horizontal jitter | Most of those units exhibit a subtle, but objectionablehorizontal jitter on playback. any fix? -hq comments: no there is no fix for this jitter. this is normalbecause of the smaller drum of the fl mechanism. however, if the problemis excessive then | ||
SONY |
CDXR88
|
Int. muting of audio while listening to cd | Customer complained about intermittent skipping but what ifound was unit was muting int. when unit would mute i found i lost audioout of pin5 (ic1021202). i found noise coming from ic512. | ||
SONY |
XR6250
|
Incorrect part no. in service manual | Unit would mute when it received a station and wasun-muted during station search. i found the 9 digit part no. for q-406was incorrect. it is listed as 872990439. also, q-403 is incorrectlylisted with same part no. | ||
SONY |
CDXA20
|
Unit will skip when playing certain discs | Customers discs, chris isaak, and bruce springsteen, born torun, skip on tracks 5 & 8 respectively. the customer was told the discswere bad, and acquired replacements. the new discs also skipped. thetechnician at san bruno did the tracking gain adj. wi | ||
SONY |
XR240
|
Incorrect part no. in service manual | Unit would mute when it received a station and wasun-muted during station search. i found the 9 digit part no. for q-406was incorrect. it is listed as 872990439. also, q-403 is incorrectlylisted with same part no. | ||
SONY |
CCDF40
|
Incorrect part number for ic201 | The 875232314 is subbed by 875232532 which is much larger. -hq comments: the correct part number for ic201 is 875994488. |