Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
D3
|
Laser stays on continuously | Ic-501 (cxa-1081q) has ld on (pin 10) permanently tied low.this pin normally controls the laser on output from the ic. if pin 10 islow, the laser is on. does this mean the laser is always on in this unit? -hq comments: not exactly. the power supply t | ||
| SONY |
CFS4000
|
Replacement counter belt does not fit | Replacement counter belt is too large by about 1cm. the beltis replaced by part number 3-642-544-xx. please advise us as to anotherpart number. -hq comments: the counter belt, ref. 359, part number 3-434-110-xx isreplaced by part number 3-657-035-xx. | ||
| SONY |
KV27XBR10
|
Distorted audio in srs mode, replaced srs module, sb 45r1 | Audio was distorted in one channel when in the srs mode. | ||
| SONY |
KPR36XBR
|
Ripple in picture, replaced ic-5007 | The asc reports that this set experienced the normal failureof the coil and diode on the e board and after they were replaced thepicture had a ripple going down the side. the trouble was ic5007on the e board - replaced it and pix was ok. we have not be | ||
| SONY |
KV32XBR10
|
Woo-woo sound, replaced srs module, s/b 045r1 | Verified problem in customers home. hum comes and goes,especially with male voice, on real stereo broadcasts with srs turned on. | ||
| SONY |
KV27XBR15
|
Woo-woo sound srs mode, replaced srs module see tvp sb #45r1 | Hum comes and goes especially with male voice on real stereobroadcasts with srs turned on. | ||
| SONY |
CDP270
|
D.o.a. - will not spin disc | Fok, sens, mon, mds, mdp are all normal. no action at ic-3/pin 45 spdlo. pull up ic-5/ pin 2 to 5v through 1k resistor causesspindle motor to turn. | ||
| SONY |
CCDTR5
|
Horizontal jitter | Most of those units exhibit a subtle, but objectionablehorizontal jitter on playback. any fix? -hq comments: no there is no fix for this jitter. this is normalbecause of the smaller drum of the fl mechanism. however, if the problemis excessive then | ||
| SONY |
CDXR88
|
Int. muting of audio while listening to cd | Customer complained about intermittent skipping but what ifound was unit was muting int. when unit would mute i found i lost audioout of pin5 (ic1021202). i found noise coming from ic512. | ||
| SONY |
XR6250
|
Incorrect part no. in service manual | Unit would mute when it received a station and wasun-muted during station search. i found the 9 digit part no. for q-406was incorrect. it is listed as 872990439. also, q-403 is incorrectlylisted with same part no. | ||
| SONY |
CDXA20
|
Unit will skip when playing certain discs | Customers discs, chris isaak, and bruce springsteen, born torun, skip on tracks 5 & 8 respectively. the customer was told the discswere bad, and acquired replacements. the new discs also skipped. thetechnician at san bruno did the tracking gain adj. wi | ||
| SONY |
XR240
|
Incorrect part no. in service manual | Unit would mute when it received a station and wasun-muted during station search. i found the 9 digit part no. for q-406was incorrect. it is listed as 872990439. also, q-403 is incorrectlylisted with same part no. | ||
| SONY |
CCDF40
|
Incorrect part number for ic201 | The 875232314 is subbed by 875232532 which is much larger. -hq comments: the correct part number for ic201 is 875994488. | ||
| SONY |
CCDSP7
|
Motor noise picked up by microphone. | Customer complaint of motor noise in audio. factory modon service bulletin #122 already installed. | ||
| SONY |
CCDF40
|
No playback | Scrambled picture. looks like lost horz. sync. | ||
| SONY |
HVM200
|
Does not operate | The leads on the dc-dc converter board punch through theinsulating sheet and short out on the shield below it. this damagesthe converter. | ||
| SONY |
XR530R
|
Replacement gear not working | National parts center computer substitutes 3-290-741-01 gear.old part has retainer rib inside hole. the new part does not. new partwill fall off as there is no room on top of the gear to install aretainer. please advise what is required to complete cu | ||
| SONY |
KV27XBR10
|
Video resets, each input has it's own reset for video levels | All the 27xbr chassis and kpr46cx chassis have individualreset for each video mode. our service centers and independent servicersare not aware of this and they spend time troubleshooting a video 1, 2, or3 video problem (example video 1 is brighter than v | ||
| SONY |
RM759
|
Remote control unit for kv8ad10 | Rm759 is made for kv8ad10. when used with 89xbrs(ic kv32xbr10), functions (power, vol., display), will work. channelup and down will not work. (info requested by dom s.) -hq comments: thank you very much for your information. we will issueservice | ||
| SONY |
KV32XBR10
|
No picture, replaced c-515, d-505, and r-515 | No picture - found c515 leaky which caused d505 to shortand open r519.c515 = .0047 @ 2kv = 1-162-114-00d505 = es1f = 8-719-300-65r515 = 212k = 1-215-871-91 |