Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CFS903
|
Part number listed for s302 is wrong | Part number 1-570-347-31 is a two-position switch. this isthe wrong switch. it needs to be a three-position switch. | ||
| SONY |
KV13TR10
|
Crt | Crt in unit has the crt, coil (degauss) and metal shield asone complete unit. replacement crt comes just with the crt. we need thecomplete assembly part number. -hq comments: there are two types of crts being used - one is in theservice manual. the o | ||
| SONY |
KPR41DS1
|
Spots on screen,dust between screens cleaned | There were spots on the screen, one big one toward the bottomright hand portion of the screen. took screens apart and found fine dustparticles. with a fine brush i was able to clean both screens. with thescreens rubbing together in shipping, there mus | ||
| SONY |
KPR41DS2
|
Spots on screen, see tv service bulletin # 17 | There were spots on the screen, one big one toward the bottomright hand portion of the screen. took screens apart and found fine dustparticles. with a fine brush i was able to clean both screens. with thescreens rubbing together in shipping, there mus | ||
| SONY |
STRAV910
|
Wrong part number for 6 pin output jacks j403-j405 | The part number listed in the manual for the output jacks areall the same regardless if it is a 4 pin or 6 pin jack. | ||
| SONY |
KV8AD10
|
No power | No horizontal drive. | ||
| SONY |
KV32SXR10
|
Two inch border around picture, leaky q-1560 and d-1502 | Unit had a two inch border around picture. | ||
| SONY |
CCDTR5
|
Camera will not load | Camera will not load. this is the second camera with this. | ||
| SONY |
GV8
|
Record knob | Record knob is not available. it is necessary to order entirepanel items yet the power knob, which is almost the same is available,items 12 and 10. | ||
| SONY |
XR7180
|
Unit appears dead | The unit appears to be dead but does have some leds on. some of the supplies are low. this is due to an open emitter-base junction of-317. leakage through r-363 makes the circuit look loaded down. | ||
| SONY |
TCWR510
|
Wrong part number | Part number for q-701 is not in the kansas city parts system. | ||
| SONY |
KV25XBR
|
Schematic error regarding v-pulse | From connector a-2 pin 3 on the v-pulse does not correctlyfind its way to ic-103/pin 4. after being inverted at q-127, its showngoing to ic-103 pin 15, fm trap pin 4 is shown tied to power switch line. -hq comments: thank you very much for your report. | ||
| SONY |
FD500
|
No raster - audio ok, replaced open c802 | No horizontal pulse at collector of q-802. a horizontal pulsewas present at base of q-802. collector voltage was 9vdc and the basevoltage was -3.4vdc. | ||
| SONY |
KPR46CX50
|
No white balance adj. in sm, see correction -1 | Several complaints from servicers about incorrect whitebalance. service manual does not contain white balance adjustmentprocedure. -hq comments: see correction-1, or use the white balance adjustmentprocedure contained in the kpr-36xbr service manual. | ||
| SONY |
KPR41DS2
|
White balance, refer to correction 2 | Several complaints from servicers about incorrect whitebalance. service manual does not contain white balance adjustmentprocedure. -hq comments: for the white balance adjustment see kpr-41ds2/correction-2 p/n 9-963-993-92. | ||
| SONY |
KPR41DS1
|
White balance adjustment wrong,see correction number 2 | Several complaints from servicers about incorrect whitebalance. service manual does not contain white balance adjustmentprocedure. -hq comments: please see sm correction number 2. | ||
| SONY |
KPR46CX10
|
White balance, see sm correction # 1 | Several complaints from servicers about incorrect whitebalance. service manual does not contain white balance adjustmentprocedure. -hq comments: for the white balance adjustment procedure see kpr-46cx10/correction-1, p/n 9-964-100-91. | ||
| SONY |
TCS430
|
Head wire too thick | Shielded cable from the pc board to the tape head opens on onechannel. wire i have will solve the problem but it is too thick and in-terferes with the mechanism and buttons of unit. not provided with anykind of head wire to solve these problems. is or | ||
| SONY |
SSM910
|
Wrong part number | Ic-501 is listed in the manual incorrectly as 8-729-262-72. -hq comments: the correct part number is 9-991-577-01. | ||
| SONY |
XK8D
|
Pcb change: motor, regulator | The motor pcb and the regulator pcb are no longer availablefrom kansas city parts. newer units have a combination type of pcb. |