Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
DRP1
|
Repair/exchange status | No schematic is provided for this unit only a one-pageservice manual exists. do we repair or exchange it? -hq comments: please exchange the unit. this model will be added to theexchange list. | ||
| SONY |
CCDV11
|
Quick repair of ccd-v11 lens unit assembly | Broken focus ring - zoom ok. | ||
| SONY |
KV2092AEB
|
Rear cover p/n, 4-376-474-11 | Part number needed for rear cover. -hq comments: the part number is: 4-376-474-11. | ||
| SONY |
CCDTR5
|
Door will not close | The tp arm block assembly (page 215, reference number 175) hadcome out of unit. the t protector assembly was bent. replaced theseparts (including washers and joint bar). unit would close and start toload. then unit would jam due to misalignment of tp | ||
| SONY |
ICF2010
|
Incorrect scan | After entering the lower and upper scan limit frequencies in,the unit would not scan correctly after pressing the scan start button.this also pertains to serial numbers 302902, 302903 and 303001. | ||
| SONY |
STRGX6ESII
|
Insulating mica part number | I need the part number for the insulating mica for the outputtransistors (2sc2921/2sa1215). not listed in two page service manual forthis model and different than those used in gx6es. because of the largesurface area and suction of heat-sink compound, | ||
| SONY |
D160
|
Replacement optical blocks | Replacement blocks coming through with pin 3 and 4 solderedtogether on 12 pin flex connector. this is just a little drop of solderwhich can easily be overlooked and cause the block not to work wheninstalled. this also is true on other models. | ||
| SONY |
D180
|
Replacement optical blocks | Replacement blocks coming through with pin 3 and 4 solderedtogether on 12 pin flex connector. this is just a little drop of solderwhich can easily be overlooked and cause the block not to work wheninstalled. this also is true on other models. | ||
| SONY |
D9
|
Replacement optical blocks | Replacement blocks coming through with pin 3 and 4 solderedtogether on 12 pin flex connector. this is just a little drop of solderwhich can easily be overlooked and cause the block not to work wheninstalled. this also is true on other models. | ||
| SONY |
D4
|
Replacement optical blocks | Replacement blocks coming through with pin 3 and 4 solderedtogether on 12 pin flex connector. this is just a little drop of solderwhich can easily be overlooked and cause the block not to work wheninstalled. this also is true on other models. | ||
| SONY |
D2
|
Replacement optical blocks | Replacement blocks coming through with pin 3 and 4 solderedtogether on 12 pin flex connector. this is just a little drop of solderwhich can easily be overlooked and cause the block not to work wheninstalled. this also is true on other models. | ||
| SONY |
CDXR79
|
Replacement optical blocks | Replacement blocks coming through with pin 3 and 4 solderedtogether on 12 pin flex connector. this is just a little drop of solderwhich can easily be overlooked and cause the block not to work wheninstalled. this also is true on other models. | ||
| SONY |
CFS902
|
Part number listed for s302 is wrong | Part number 1-570-347-31 is a two-position switch. this is the wrong switch. it needs to be a three-position switch. | ||
| SONY |
CFS903
|
Part number listed for s302 is wrong | Part number 1-570-347-31 is a two-position switch. this isthe wrong switch. it needs to be a three-position switch. | ||
| SONY |
KV13TR10
|
Crt | Crt in unit has the crt, coil (degauss) and metal shield asone complete unit. replacement crt comes just with the crt. we need thecomplete assembly part number. -hq comments: there are two types of crts being used - one is in theservice manual. the o | ||
| SONY |
KPR41DS1
|
Spots on screen,dust between screens cleaned | There were spots on the screen, one big one toward the bottomright hand portion of the screen. took screens apart and found fine dustparticles. with a fine brush i was able to clean both screens. with thescreens rubbing together in shipping, there mus | ||
| SONY |
KPR41DS2
|
Spots on screen, see tv service bulletin # 17 | There were spots on the screen, one big one toward the bottomright hand portion of the screen. took screens apart and found fine dustparticles. with a fine brush i was able to clean both screens. with thescreens rubbing together in shipping, there mus | ||
| SONY |
STRAV910
|
Wrong part number for 6 pin output jacks j403-j405 | The part number listed in the manual for the output jacks areall the same regardless if it is a 4 pin or 6 pin jack. | ||
| SONY |
KV8AD10
|
No power | No horizontal drive. | ||
| SONY |
KV32SXR10
|
Two inch border around picture, leaky q-1560 and d-1502 | Unit had a two inch border around picture. |