Sony Repair Tips
Search: sony
Results: 20073
Results: 20073
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
ITA650
|
Impedance of sony telephone products | What is the impedance of our phone products? -hq comments: all sony phones fall in the range of 50 to 300Ω whenthe phone is off-hook and when dc-loop current is in the range of 15 -120 ma. | ||
| SONY |
ITA600
|
Impedance of sony telephone products | What is the impedance of our phone products? -hq comments: all sony phones fall in the range of 50 to 300Ω whenthe phone is off-hook and when dc-loop current is in the range of 15 -120 ma. | ||
| SONY |
ITA550
|
Impedance of sony telephone products | What is the impedance of our phone products? -hq comments: all sony phones fall in the range of 50 to 300Ω whenthe phone is off-hook and when dc-loop current is in the range of 15 -120 ma. | ||
| SONY |
ITA500
|
Impedance of sony telephone products | What is the impedance of our phone products? -hq comments: all sony phones fall in the range of 50 to 300Ω whenthe phone is off-hook and when dc-loop current is in the range of 15 -120 ma. | ||
| SONY |
CCDF70
|
Noisy picture | One head output is missing. | ||
| SONY |
CCDF50
|
Noisy picture | One head output is missing. | ||
| SONY |
FD10A
|
New back plates do not fit older units | Older fd-10a (i.e. - 1986 models) were manufactured in japan,newer models were made in taiwan. band sw is in different positioncausing a misfit of replacement plates on older units. -hq comments: cabinets (rear) assembly for both old and new fd10a area | ||
| SONY |
CDXR77
|
Clock and date goes blank intermittently | Clock and date display goes out intermittenly. the two dotsfor indicating time and one for date stay on and can be changed withdisplay button. back light condition stays as set. all radio and cdfunctions work properly. | ||
| SONY |
FDL320
|
No picture, audio ok : flourescent lamp, fr-801 | Picture goes blank after two or three seconds. | ||
| SONY |
KV32XBR15
|
No manual power on, change c-125 to 2.2/50v bi-polar | Unit has no manual power on/off. there is a hole for d-106in reset circuit. no component is there, instead there should be c-115.if diode is inserted in reverse direction unit will work. in manual powermade, unit has a power and reset pulse required t | ||
| SONY |
KV32XBR10
|
No manual power on, see sb # 40, c-125 replaced with bipolar | Unit has no manual power on/off. there is a hole for d-106in reset circuit. no component is there, instead there should be c-115.if diode is inserted in reverse direction unit will work. in manual powermade, unit has a power and reset pulse required t | ||
| SONY |
TAAX390
|
Missing part numbers - output transistors | No part numbers listed for output transistors, q511, 512, 611and 612. | ||
| SONY |
KV8AD20
|
Tuning indicator | Tuning indicator bar is 1/8 inch shifted from thecorresponding channel numbers. can this be corrected? -hp comments: this bar can not be adjusted. its length versus channelnumbers is determined by ic program (icoo1). | ||
| SONY |
SLV757MC
|
Tape stabilizer loose in unit | Tape stabilizer guide rolling around loose in transport -customer pulled out through cassette door. second unit with sameproblem. | ||
| SONY |
GEN-TVP
|
Sap broadcasters in ny have changed audio information | I received inquiry concerning why there were no longer radiobroad casts on sap mode on channel 41, 11, 9. according to the individualstations engineering departments, music program has been replaced with amono duplicate of tv stations programming. | ||
| SONY |
KV27XBR10
|
Schematic error, diode d-106 not used, refer to tvp flash 37 | Page 38 of service manual shows d106 between pin 1 of ic101and l101. | ||
| SONY |
WMA12
|
Original motor is still supplied | The motor in this unit is a approximately 1 inch across withmounting screw holes approximately 7/8 inches apart. the replacing motoris approximately 7/8 inches across with mounting screw holes approximately3/4 inches apart. -hq comments: apparently the | ||
| SONY |
CDXR77
|
Missing part number - feed guide for optics | The part number for the feed guide shown on page 45 of thecdx-r79 manual above the optical block reference 926 is missing. do youhave a part number? -hq comments: the part number is 2-640-654-03. please add this numberto your service manual. | ||
| SONY |
CDXR79
|
Missing part number - feed guide for optics | The part number for the feed guide shown on page 45 of thecdx-r79 manual above the optical block reference 926 is missing. do youhave a part number? -hq comments: the part number is 2-640-654-03. please add this numberto your service manual. | ||
| SONY |
GENERAL
|
Part numbers of double sided tape | When either the 6mm wide (7-632-453-52) or 9mm wide(7-632-453-53) double sided tape is entered in the computer for ordering,both are subbed to 9-910-999-88. this is a number that has (unnecessaryfor normal repair) for a description. please advise how w |