☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20088
Make Model Symptom Problem Solution By
SONY AA-2W
AA-2W 		Distorted image at the top, like wind or as if tsound were scratches at the top, as a sign of noise. the image in the middle is like a gear tooth, shaky. normal sound Clean the contacts wsound the pp cable enters, that is, the female connector of the pp tuner with caool and the male of the cable as well. check the projection on the back cover wsound the pp cable passes, make sure it is not crushing or breaking the cable. If necessary, break the projection.
SONY KV-1439B/2159B/1440B -2160B
Vertical synchronism instability. the image scrolls or just shakes Eliminate q311, r315, r329, r330, r331, c329. short the r315 and c329 on the main board with a 5mm wire.
SONY BA-3B
BA-3B 		I'm sound Disconnect pin 46 on the computer, see if it works again. add a 12v zener between r040 (negative side) and the positive side of the zener to r268, all on pin 46. to prevent the audio IC from burning you can place a zener diode in place of the jw110 jumper, with the cathode facing towards the audio ci251 (tda2009). If tsound is no result when adding the zener to the PC, replace the PC or eliminate the SMD muting transistor to see if the sound returns. (except that the muting would be lost when changing channels).
SONY BA-3B
BA-3B 		Turns off by itself, volume and channel switching do not work, or it could be one of these isolated defects Change the cf001 crystal. ( attention The 2sc4834 transistor is irreplaceable, insert original. 2sc4034 is not compatible, it is printed wrong on the schematic).
SONY KV-2158B/62/63S/KV-1441B
Loud noises, in quieter places you can hear even more Place a covered wire between the ground terminal of resistor r505 and the positive terminal of c515. the wire must be close to the plate, do not pass over the plastic support.
SONY KV-2162/63S
If the customer complains that the TV does not have good image quality, with a lot of grain appearing, do this Change the c379/380/381 values ​​from 560pf to 270pf. If it doesn't work, remove the 680pf c382. these chapters. are located on the ic351 terminals.
SONY KV-2162/63S/KV-2158B
To prevent q551 from burning Replace the 4.7k r555 with a 6.8k/2w one, even if you didn't change the same tsh q551.
SONY KV-2162/63S/KV-2158B/KV-1441B
After a few minutes of operation the TV loses its brightness Connect a bus generator and select white standard (75%) and adjust the rv353 to obtain 50+/-10mv at TP48 on board “a”. Leave the TV on for about 30 minutes. If you don't have a generator, do the following Tune in to a station and wait for the screen to darken. turn the rv353 to the left until the image returns to normal.
SONY KV-2959
Burns the power supply oscillator transistors Check if this TV has a jumper in place of the r662, if so, remove it and place a 10r-1/6w resistor to dampen the starting current.
SONY KV-29V55/34V55
Vertical instability. At some point, the customer may complain that the TV has a crumpled vertical display, the image may shake, jump, or not stop running Eliminate r335 and eliminate and short r343. only on TV that presents these anomalies.
SONY KV-2970T/3954T
Lack of vertical height See r563 changing +/- to 3.0Ω it changes the vertical, even increasing the adjustment.
SONY KV-29T75/T80
Tinnitus Distance c507 from d501 from the main “a” board. remove the coil l501 from plate “a” and replace it after gluing it with quick glue. It is similar to the fly buzzing.
SONY KV-29V55/34V55
Mat leakage and charring of the print track leaving pin 8 or 10 of the fly t501 Remove the r550/551 and place a 0.5mm jumper with wire. remove the c550 (0.068mf/200v) and place it in position c510 next to the fly.
SONY KV-29XTR20
Does not tune the channels Broken solder on inductor l101.
SONY KV-34/38FV15B
The left side of the screen is darker than the right side Remove the L504 coil (100mH inductor) from the PCI and change its face, that is, change its position by 180 degrees. jumper jw938 put a 1m resistor. the c976 of 2700pf put another of 820pf. 12k r974 put 4.7k (smd).
SONY KV-36XBR800
Purity failure in 220v network Replace the 2.2mf/50v c6809 for a 47mf/50v one. Leave the TV off for 30 minutes, then turn it on and see if the stains are gone, if not, follow the procedure mentioned above.
SONY KV-36XBR800
Smudged screen in 220v area If demagnetizing doesn't work, do this. Tsound is a small plate directly underneath the TRC, well, disconnect the CN6805 connector with the TV unplugged. Turn on the TV to see if tsound are any stains. Now turn off the TV and reconnect the connector. (This procedure cannot be repeated more than once).
SONY KV-38FV15B
Remaining spot when turning off the TV Change the c1794 of the 4.7mf/250v “c” board to a 22mf/250v one (trc board).
SONY KV-9AD10
Fabric stain Demagnetize the trc. This TV does not have an automatic degausser.
SONY KV-25FV10B/KV-29-34-38FV15B
Image without color (main screen and pip screen) In the first model, change the c320 without measuring. in others, replace the c309. on the pip board swap c3366.