Repair Tips

Search:
Results: 87727

Make	Model	Symptom	Problem
SONY	XR33	No part number for s903 - muting sw	No part number listed for s903 (muting switch).
SONY	D5	No operation of the unit	The converters +5 volt output fails because of an intermittentshort between the two wires leading to the laser power switch (s901).inspection of these wires may not yield any obvious insulation breakseven though you can measure a short when pulling on th
SONY	KV2792R	Light picture, no ch would tune in, replace r-1576	The unit would turn on, but had a light picture washed out.could not tune in any channels. video could be received but light pix.
SONY	SLHF300	Need part # - right lock base	Can you provide me with the part number for the circledlever? -hq comments: part number is 3-684-232-02 which is called lock (right)base and is available at kcp.
SONY	KP5000	Overall green tint on upper 1/3rd of projection screen	The upper 1/3 of the screen has an overall green tint to thepicture/program material. i have also seen 2 other kp-5000 projectionsystems recently with the identical problem. -hq comments: please clean crt surface. it will be necessary to removelens as
SONY	LCV	No part numbers for camera case parts	Customers need parts for various camera. -hq comments: plealse contact me directly if you need any specificparts. we can get them through sales or tokyo. during our internationalserviceability meeting in tokyo, we will suggest making these partsavaila
SONY	SLHF1000	Flagging during playback in special effects mode (bis)	Picture flags during special effect playback in beta is mode.is this normal? -hq comments: i checked our lab unit and there is no evidence of anyflagging. please try adjusting tape path and inform results.
SONY	RM717	No channel 3 function	The conductive coating on the ch. 3 pad is worn off and thisfunction will not work. the remote works on all functions except thech. 3 button. bulletin should be produced on disassembly procedured onremotes and the fix for this problem.
SONY	RM724	Intermittent remote	No ch. up/down or volume down. conductive coating on pad isworn off on functions that will not work. this problem is becoming biggerand bigger. many remotes are being replaced. many shops do not know howto open these units so they never want to repai
SONY	CFS9000	Tracking noise in audio	When using the d-14 and the cfs-9000 on the same dc power supply,there is a noise in the audio that is equal to the tracking changes onthe d-14. the noise can be seen all over the d-14 including the ground,when the scope ground is connected to the dc supply g
SONY	SPP100	Insufficient range	Maximum range is 20 to 40 feet. checked base unit output -low. checked handset output - low. is there another procedure for txpower adj using a dvom or a scope? an rf power meter is not in every ssc.
SONY	SDP505ES	Will not function	Display erratic. no functions. display is cycling as if intest mode.
SONY	KV20XBR	No picture, 200v lead and one filament lead broken off	Servicer told me that he just repaired 3 sets with the 200vlead and one filament lead broken off right at the board (c board) connec-tion. it is possible that there may not be enough slack in the leadswhich could cause the problem.
SONY	XR780	No am or fm operation	No am or fm. dc voltage at emitter of q225 was 7.4vdc insteadof 8.8vdc. although the regulator transistor (q225) did not check open orshorted, it would not function in the set.
SONY	KPR4620	Upward bending - vertically up to 2 inches	Picture distortion-bending on top left edge of picture (verti-cally up to 2). produced only when playing back prerecorded tapes on rca(2 head) vcr deck. also the same identical problem is produced when usingsony evs-700u 8 mm video deck, but in the slo
SONY	HVC1000	P/n for lens assembly	No p/n in service manual. -hq comments: refer to page 4-4 of s/m. part no. 1-547-030-21(incorrectly listed as -12) is the chassis assy including lens. pleaseorder under this part no.
SONY	SLHFR30	Distorted audio, video on rf output only	Picture overload, bending, buzz in sound, only when using rfoutput. pix and sound ok at video output jack.
SONY	CCDV3	Tape path	Noise bar in picture and no vertical sync (rolls). foundentrance guide #3 loose causing tape path alignment to be off.
SONY	XR787R	Unit was stuck on 530 am	Unit was stuck on 530 am. clock worked when radio was turnedoff. no buttons would operate. tape also would only cycle thru theneject.
SONY	CDP25	Wow distorted audio	Distorted audio.