Cce Repair Tips

Search: cce
Results: 4816

Make	Model	Symptom	Problem	Solution	By
CCE	29US	Shadow right side 10cm	Change c406 changed		Francisco
CCE	HPS-2073	No signal in rf (av perfect signal)	R108 (12k) on the 33 volt line of the varicap	Replace the same	Jarbas Santos (Eletro-serv)
CCE	HPS2991FSF	The TV would turn on and light up the filament, but the tube would not open.	After a lot of brainstorming, I found a defect in the RGB which was in the diodes d903,d904,d902	After the replacement it was amazing.	chines eletronica solanea PB
CCE	2071	TV does not turn on power supply without pulse, LED is off	Q806 remove, the TV works ok.		oficinaeletronica
CCE	HPS-2071	Power supply oscillating (pulsing sometimes it doesn't turn on	Q806	Replace it (in my case I removed it and the TV worked normally)	antonio nobrega (patos pb)
CCE	HPS2171FS	Without image, with normal characters.	Change without testing cap.424 on the abl line	Cap 424	DEBIQUE
CCE	HPS2046	Jagged image in the upper half of the screen, sometimes without sync.	Chap. c405 and/or c404 - leakage and/or loss of capacitance	Replace them	SADER
CCE	HPS-2991FS	TV not working LED lights up with a little buzz in the drive	Electrolytic capacitor of 100uf 160v c= 826 close to zero drain of oxidized mf comptos	Replace and analyze	ELETRONICA MEDEIROS
CCE	HPS-2007	Does not turn on +b power supply low and stanby led off @@@	Tl431		EETRONICA ARNI-L. LEAL- SC
CCE	HPS21AVP	Turns on and then turns off	Capacitor417 (330pfx2kv)	Replace of the same	Julio Cesar (This email address is being protected from spambots. You need JavaScript enabled to view it.)
CCE	HPS2901	Jagged image	Solda fria no d400(smd)		HP ELETRONICA
CCE	HPS2007E HPS2002 HPS2004	D805 bav21 with small leak	Voltage on pin 7 of ic801 only 5v	D805 bav21 with small leak	jasvan souza
CCE	HPS2071	LED blinks TV won't turn on	Fr 401 changed or opened.obs. could be cold welding		Marcos
CCE	TV2118USP	Just put it 015r and the power supply will stabilize	When there is no r813 in the circuit	Just put it 015r and the power supply will stabilize	alpha eletronica
CCE	HPS-2004	It turned on normally -> sound, image in a few minutes only sound without image	(measuring base q401 has dc voltage when connected 0.5v to 1v), =, and on the base of q402 it does not measure anything alternately you can change q401(mpsa42a)	Q401(mpsa42a)	Alextecnico
TV CCE	HPS 2171 FS	Power supply pulsing with low voltage. blinking led	Zd 809 10v		severino alves
CCE	HPS1470	No horizontal part	R412 se 4k7aberto!		orlando lott
CCE	TV2910FSD	Closed horizontal	Check these components q409,c409,c432 and r407 the cause is the caps that run out	Replace them and it will be beautiful	eletronica newtec
CCE	HPS2985 HPS2971FS	Burning primary supply regulator q803	It looked like flyback, but it was c402 (331 j) shorted on the horizontal output	Replace c402	eletrônica fernandes-to
CCE - DISNEY	HDC142 FS	Doesn't start	Low supply, activating eht protection, disconnecting pin 34 of the microela works, dz401 changed, measuring is good, however the voltage at its terminals is high, causing the protection to fail, there is no point in measuring analogically, changing directly.