Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS2003 D	TV does not come out of standby	Dz 702	Resolder it or replace it.	eletronicaapolo
CCE	HPS2171/2073/2071		Oscillates width and +b1 according to brightness	Desolder and measure r812 r813, and if d816 and d817 are open they will certainly be shorted	jasvan souza
CCE	HPS1405	With reduced u-shaped frame closed on the sides and bottom.	Tda8841 with low horizontal frequency.	I replaced the tda8841 and everything went back to normal.	<small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
CCE	HPS2003	When activating power, the LED turns off but the TV does not turn on	All secondary voltages were ok as well as the power supply to the two cis	Transformer t401 horizontally with one of the windings open after the replace, the TV started working again	JOSÉ GUSMÃO
CCE	HPS2971	Closed horizontal	C409 (560pf) open or with low capacitance	Confirmed orlando	aelson
CCE	HPS 2171FS	Turning off with vertical closed	Fly-back pino 9 +12 0v	Replace	EMERSON RIBEIRO
CCE	HPS 2997	Turning on and off	The two BC's with leakage q802/805	Replace the two bc's q802/805	rúdson
CCE	HPS 2971	Image expanded according to brightness	After searching through many abl tips, I mistakenly downloaded the schematic of another model that uses the same power supply (2991) and found that in the original schematic r813 has a value of 1.5 r while in the hps 2991 schematic it was 0.15 r	Just replace the 1.5 r resistor (which is wrong in the original diagram) for a 0.15 r one like this in the hps 2991 diagram and go for the hug, phewwww	edgar
CCE	HPS 2980	Def chroma, green face	Ic 501		helio
CCE	HPS1497P	Stop	Cq0765rt	Just replace it and everything is fine	Rafael
CCE	TV2118USP/AV	Viola effect	D 409 with fuga	I replaced it and everything was ok.	digitec eletronica
CCE	HPS-2097-1497	Turning off in 5 seconds LED blinking non-stop	Dz401 4v7 with leak	Turn off the collector q403 and q404 if the TV stops turning off the defect is the dz401 just replace it	beto2828
CCE	1471	TV blinking LED does not turn on	Transistor q802	Zero seradinho	MARCIO
CCE	HPS - 2001	Vertical closed without sound	Solution: replace ci-301(tda - 9309)		BARRETO CRUZ
CCE	HPS2198AV	Stand-by lights up, power supply has 98v 3 10.2v when turning on power supply drops to 87v and 9v and returns to stand-by.	Ci power supply oscillator tda1533at		WAGGUINHO
CCE	HPS2185FS	Strip on the left side of the screen, approximately ten centimeters wide.	C825=100ufx160v,no capacity.	It was replaced and resolved...	Armando Eletronica EvoluSom Olímpia.
CCE	HPS2991FS	Altered power supply b+ with 170 v	R816 the 130k		jair capitão poço PA
CCE	HPS1405	With audio without image and without high voltage, checking the 15,750 kHz signal was reaching the base of the horizontal output but the voltage in the pre collector was low.	C410 with leaks on the scale of x10k, replaced the capacitor c410 arrived in the image and consequently the high voltage can be of use to some friends here in the forum, a hug to everyone.		<small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
CCE	HPS 2071	LED keeps flashing and the TV doesn't turn on, there's a +b missing on the flay-back	Change fr 401 that was open		pedrinho telaquente
TV CCE	29USP	Fat image with color retrace the straight one is crooked resistor fr423 heats up a lot and burns	Capacitor 406 is burning		wilson