Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
HPS2071
|
LED blinks TV won't turn on | Fr 401 changed or opened.obs. could be cold welding | Marcos | |
CCE |
TV2118USP
|
Just put it 015r and the power supply will stabilize | When there is no r813 in the circuit | Just put it 015r and the power supply will stabilize | alpha eletronica |
CCE |
HPS-2004
|
It turned on normally -> sound, image in a few minutes only sound without image | (measuring base q401 has dc voltage when connected 0.5v to 1v), =, and on the base of q402 it does not measure anything alternately you can change q401(mpsa42a) | Q401(mpsa42a) | Alextecnico |
TV CCE |
HPS 2171 FS
|
Power supply pulsing with low voltage. blinking led | Zd 809 10v | severino alves | |
CCE |
HPS1470
|
No horizontal part | R412 se 4k7aberto! | orlando lott | |
CCE |
TV2910FSD
|
Closed horizontal | Check these components q409,c409,c432 and r407 the cause is the caps that run out | Replace them and it will be beautiful | eletronica newtec |
CCE |
HPS2985
HPS2971FS |
Burning primary supply regulator q803 | It looked like flyback, but it was c402 (331 j) shorted on the horizontal output | Replace c402 | eletrônica fernandes-to |
CCE - DISNEY |
HDC142 FS
|
Doesn't start | Low supply, activating eht protection, disconnecting pin 34 of the microela works, dz401 changed, measuring is good, however the voltage at its terminals is high, causing the protection to fail, there is no point in measuring analogically, changing directly. | ||
CCE |
HPS-2171-FSH
|
Completely stopped, not even the LED lights up. | Change the capacity. electrolytic power supply. (150mf 400v) dry. | elet.washington | |
CCE |
HPS-1407
|
TV stopped with all normal power supplys (when you turn on the power, the LED blinks indefinitely. | C-825 - 47/160 (disabled) | Just replace it and go for the hug....... thanks everyone for the tips (god bless you) | |
TVCCE |
HPS2991FS
|
When turned on, the image takes a while to appear or no image appears at all. | +b normal, filament lights up normally, has high, normal screen and normal power supply. | Q-905 with cold welding on the tube plate. | Adilson(formiga-mg)-email= |
CCE |
HPS2981C
|
TV stopped doesn't turn on. | Due to poor contact on the horizontal deflector coil socket pin, pin referring to the horizontal circuit. Due to this poor contact, the horizontal output tr was shorted and after changing it, the TV worked with a normal image, but without sound. I then discovered that the ,q 602=bc547b was shorted in the sound output pre. | The horizontal output tr and the q602 =bc547b sound pre were replaced and it looks great. | Armando de olímpia Eletronica EvoluSom |
CCE |
HPS2097
-------- |
A black band on the left and right side of + - 2cm in the vertical direction, and immediately turning off.power supply+b with 97v. the right one is 102v. | C825 low cut | Replace c825 de 47mf p/ 160v | Ademir tc |
CCE |
HPS-2997FS
|
Dark screen (no weave) | C409(394j/250volt)poliester | Replace it without testing | Jarbas (ELETRO-SERV) |
CCE / CYBER VISION |
HSP2991 / TP-2958
HSP2991 |
When pressing the "on" key, the TV turns on but does not accept commands from the control and the screen remains off. | When activating the service menu function 02 (vsd), the controller causes the standby system to malfunction. | Place a switch between pin 78 of the TDA (central processor) and the board's ground. When pressing the on button, immediately after holding down this previously soldered service button for 30 seconds, after releasing it the TV will turn on. Press the service button twice again and the TV will enter service mode, then enter 96 and replace the option to "02". press osd/out to exit and that's it! | Paparotti |
CCE |
HPS2197
|
Turn on turn off | C825 47uf 160v with leakage | Replace of the same | orlando lott |
CCE |
2118USP/AV
|
Burning of the horizontal output transistor | Capacitor position 419 defective and just replace directly without measuring | ||
CCE |
HPS2181
|
Going out of tune | T103 | 4.7pf mini tubular capacitor inside the damaged t103 coil, break it and place a 4.7pf ceramic capacitor. under the plate | FERNANDO ALCANTRA DE OLIVEIRA |
CCE |
HPS2071
34BI |
Turns on when cold and then turns off after a few minutes. When it heats up and the stand-by LED flashes | Fr401 (1Ω) damaged or cold soldered, located in the horizontal deflection circuit | Replace fr401 or re-weld | TECNOGUEDES |
CCE |
HPS - 2071 FSG
34BI |
Turns on, the image appears and disappears as quickly as a blinker. | Replace capacitor 825 (47uf/160v.) | BARRETO CRUZ |