Cce Repair Tips

Search: cce
Results: 4816

Make	Model	Symptom	Problem	Solution	By
CCE	HPS2981	Channels going out of tune	T103	Replace t103 replaced	ELETRONICA MAURI JUNIOR
CCE	HPS2991	Three vertically one centimeter long sparkles of brightness, one green, red and blue. at the top of the screen, with high voltage and no sound. When speeding up the screen, the screen without vertical scanning appeared, and the sound appeared.	C408 (4,7mf/160), c409 (390k) c408com 0,58mf		Ademir tc
CCE	HPS 21AVP	Turns off after turning on	C417 with leak	Replace for a new one, TV is ok! #let's help, post your tip#	andlss (AL TECNOLOGIA)
CCE	TV-2118USP	Turns on and off sporadically, LED flashes	Cold soldering on d807	Resolder this component and the others nearby.	Evandro Estrela
CCE	HPS2071	Dull	C424		Andrade
CCE	HPS 2997FS	Lacks brightness, as if the kinescope were weak, screen, filament everything ok!	Abl line defect	Resistor r423 1k open	marcelo marques
CCE	2197FS	It takes a while for the image to appear, the screen adjustment does not give good results, it keeps blurring at the top of the screen, but at the bottom it keeps freezing, sometimes it works normally	Changing the socket on the tube plate and capacitor next to it from 1k to 2k2		WISLEN
CCE	HPS2991	It was without capacity, leaking and the mug didn't inflate.	Replacement of capacitors c825 and c 831	It was without capacity, leaking and the mug didn't inflate.	takashi murata
CCE	TV 2118USP/AV	Screen slowly darkens	RGB voltage goes to the limit	I replaced the tr on the kinescope plate. v 923, if you don't want to waste time, replace the 3 bf 423	FERNANDO DA SÓ CONSERTOS
CCE	HPS2971C/HPS2983 HPS2971	Turns on and off for 2 minutes, turns off, works well, before turning off images suffers a horizontal type of interference out of frequency, and goes into protection and turns off.	Capacitor burning internally, c 406 (330 pf 2kv) connected to the horizontal output collector.		ELETRÔNICA MOISES
CCE	HPS21AVP	When turned on from the dark bar on the left side of the viewer, it immediately turns off.	Change c417/ 330 pf, "be careful, it measured 380 pf on the capacimeter, but 6 mega of leakage"		RUI
CCE	HPS 2007	Three vertical lines red green blue	C 301	Replace c 301 1x160	felex
CCE	TV2118USP VER2.2	This TV had burned out the ic n511 cq1265rt power supply regulator So far everything was fine, I bought the component and replaced the guy but the TV didn't work and between the terminals of the zd517 the current kept oscillating, I tested and replaced almost all the components of this circuit but It didn't solve it, I had already tested c541 with the capacitance meter and it measured with a tolerance of 5 to 10 percent, so I decided to replace the 220uf/160 volt guy with a 470uf/200volt just to clear up this single doubt and then I just ran for the hug .	C541 exchange for one of equal or higher value		fabiusmax
CCE	HPS 2007	Dark screen, with a vertical line	Capacitor c 409 394j, electrolytic capacitor 4.7 x 160 v, resistor 15 k	Replace of components	Adenilson Boscolo
CCE	TV2918USP	There are traces in the corner of the image, which increase when the TV is turned off.	C402,331pf		Eletronica benedito
CCE	HPS 2971	Turns on the LED, turns off but does not generate an image	C 409 dry and r407 altered	Replace them	antonionobrega(patos pb)
CCE	HPS 2171 FSG	Vertical lines of linearity top	Fly pacifier cable leaking, discharging in the yoke, after solving this fact, this defect arose, after testing all the components of the vertical, I decided to change the v output.	Changing the vertical output, stv9325 or la 78040 (equivalent)	eletronicadoalemãThis email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS-2118C	Turning off after a few seconds, going into standby.	Q804, with small leak.	I replaced the q804, bc337. If not, I used the bc639, which is equivalent, and the device worked normally again.	Tulio
CCE	HPS3407	Width does not work (expanded screen)	Inductor l405	Coil replace	DEBIOUE
TVCCE	TVS-2910	Sometimes when you turn on the TV, the LED goes out, but the blinking image does not appear.	Check the two conds (c829- 33mf/160v, and c825- 47mf160v), abl line and its peripherals q404 and q405, but the culprit was the altered tube socket.		Adilson(formiga-mg)