Cce Repair Tips

Search: cce
Results: 4834

Make	Model	Symptom	Problem	Solution	By
CCE	HPS-2991 FS	No sound and no image; normal voltages and lit filament; When adjusting the screen the screen becomes white with trace lines.	Altered filament tension.	Put a resistor (1r) in parallel with l400 (it is close to the fly-back)	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS 2971	LED goes out as if it were going to turn on and it doesn't turn on	C 422 shorted near the tsh drive		rpsilva
CCé	HPS 2971J	Blurry image looking like a weak tube	I researched the ABL line and changed the 22nf 250v electrolas	Replace l 400 or put a jumper	luiztvsom
CCE	HPS1471FS	The TV turns on and then turns off by itself.	Cause of the defect, q802=bc337, leak between base and collector, the touch switches were also changed, in the volume minus menu, volume plus and channel minus.	Q802=bc337 and the four touch keys that were failing were replaced and the TV looked great.	Armando de olímpia
CCE	HPS21AVP	A dark band horizontally.	18k open resistor r414	Substituição do resistor r 414 18k	WAGGUINHO
CCE	HPS 2991FS	Starting generates high voltage but immediately activates the protection.	Capacitor de 330kx2kv na posiÇao (c402)	After changing it, the TV worked perfectly again.	DIGITEC ELETRONICA Lambarí D'oeste -MT
CCE	HPS2118	TV doesn't turn on, LED is off.	Q804=bc337 shorted, there was no 5 volts.	Replaced and resolved.	Armando de Olímpia
CCE	HPS 2997 FS	This TV had the following defect; It would light up on stand - by, I would press power and the LED would turn off, the power supply would normalize at 135 volts. But there was no image or sound, the filament wouldn't light up, the screen was at 200v and the TV didn't activate any type of protection.	In my case the defect was the capacitor c 409 completely depleted.	Replace c 409 390nf/250v	chinês eletrônica solânea/pb
CCE	HPS144	Turning off with vertical closed	Q 802 and q804, replace even if the mark is good		eletronicard
CCE	HPS-2185 FS	Before changing the ic tea 1533at, the TV doesn't even turn on, the LED is off, now after I changed it. When I unplug it, it makes three beeps as if there was a shorted capacitor. I already did a test but I didn't find anything. Anyone who knows can give me a tip.	*	*	francisco
CCE	HPS2997FS	TV turns on, filament lights up and there is no image or sound and the screen does not work	Open resistor r930 on the screen line, I removed it and put a jammer on it because the schematic doesn't show this resistor and the TV was ok		HEMERSON ELETRONICA MM
CCE	HPS 2197 0022866	Burning bu 1508	Pickled tube	Replace the tube	karpinski
CCE	HPS-21AVP-2071-2073	It doesn't come out of stand by, the LED keeps flashing and the relay hits	Hsyn pulse with 4v, even though the TV is in STD by, it should be 0v	Capacitor c417, 330 pf/2kv with imperceptible leakage, it is the same one that also causes the defect of moving the image a little to the side, replace	jasvan souza
CCE	HPS 2901		Blurred color looking like a tube	Replace of r 904	ignacio gomes neto rio verde ms
CCE	HPS2971	Stand by LED on but not turning on	C825 totally dry sem capacitance	Put a new one in place and the tv worked normally	ELETRÔNICA NUNES
CCE	D32 LED	The stand-by light comes on, + it kept blinking and didn't turn on	Removed the transformer from the power supply and found oxidation on the board at the base of the transformer pins	Cleaned the place where the transformer pins were soldered with a piece of 200 grit sandpaper and turned it on normally.	ROBERTO PINTO
CCE	TL660	Call and add image	Turn it on and add the image		claudio
CCE	HPS 2171 C	Burning q-801 and crashing rl 801	Fr 802 100r changed /// hitting rl801 diode d-819 partial short	With the replace fr 802 100r stopped burning the p10nk80 / beating rl801 was replaced d-819	Wislen Alves
CCE	HPS2118	The LED doesn't light up, but there is noise in the speakers, like a heartbeat, the power supply pulses	C808: 22x25v changed	Just replace it for a new one	Paulo Sertel Itararé SP
CCE	HPS 2997FS	Device does not turn on. main supply of 132.5v, with only 60v.	Ic 802 tl431 pino 1 aberto; c825 100mf/160v aberto.		JONAS DE MOURA