Cce Repair Tips
Search: cce
Results: 4816
Results: 4816
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS2991
|
Turns off after a few minutes | Changed q 804 | cleberlima | |
| CCE |
HPS 2971
|
TV works, but the screen expands when changing the brightness and contrast. | Replace sem test diode d 415 ch. 441 ch. 442 | Diode d 415 cap.441 cap 442 | DEBIQUE(ELETRONICA ROBSON) |
| CCE |
2997FS
|
It doesn't turn on, it just keeps the LED on | Does not oscillate | Replace the transistors: q802 and q805 with bc 317 and the capacitor 835 with 47μF 25v | LUCIAN |
| CCE |
HPS 1471 FSJ
|
This TV programs the channels and sent it to the customer's house. He said that it started to disappear, the image was just a blue screen, I checked the memory, seletronique, the diode that feeds the ci communication ports with seletronique, everything was ok; | Transistor q101 with leakage. I replaced it and it got zero bullets | moroni eletronica | |
| CCE |
HPS-1415
|
Doesn't start | Ic 501 | Perse | |
| CCE |
HPS-1480
|
Without contrast adjustment | D290, d704 | Perse | |
| CCE |
HPS-1485
|
Turns off and on without more or less | C499 (1 µf 250 v) | Perse | |
| CCE |
HPS2004B
|
No image, and sound ok. The voltages were all correct, I checked the usual horizontal output components, cap, resistors and everything was ok. | Resolder parts that suffer excessive heating | Perse | |
| CCE |
TV-2918USP
|
Image shaking and pulling to the right with horizontal stripe to the left | C402 | Replace | ÁdrianChapadão |
| CCE |
HPS1481
|
TV arrived at the workshop with bu 1688 burned out, so I replaced it but the TV continued to heat up the bu a lot, I looked in the horizontal dryver and found two very bad capacitors c406=1mfx100v, c408=10mfx100v, I just changed them and the horizontal bu no longer overheated | I just swapped them and it was fine | ||
| CCE |
HPS 2991
|
Weapon and disarm | Defective capacitor c869 | Put the capacitor mentioned at a value of 2200μF/63v | Bomtempo Mecatrônic |
| CCE |
HPS-2981
|
TV doesn't turn on power supply ok, it would only turn on if you desoldered base q701 | C 718,719 shorted | betoteck | |
| CCE |
TVS2910FS
|
Turning off in a row | 812 open diode | klein | |
| CCE |
HPS2081
|
Does not oscillate horizontally | Vertical output | Replace vertical output | DIGITAL TEC |
| CCE |
HPS1471
|
Image interference and sound noise | C102-smd | Replace c102 smd | CENTER SOM ELETRONICA |
| CCE |
HPS2906C
|
It doesn't turn on, it just flashes the LED, +b doesn't adjust, it varies even when the horizontal is turned off. | Circuit reg. power supply r820 127kΩ open and d812 5v1 changed. | Bruske | |
| CCE |
HPS1491
|
Vertical closed from the middle up | R303 (68k) open | ARAUJO | |
| CCE |
HPS 2092
??? |
When I turned on the TV, upper retraction lines appeared with a low horizontal range | Burnt resistor r308 - problem solved after replacement | FELIZ | |
| CCE |
HPS 2991FS
|
Screen showing phase ghosting from left to middle of the screen | Ceramic capacitor c 402 shorted and resistor r 401 burned, in the hsinc circuit | Jose Fernando - Saquarema | |
| CCE |
HPS 2997FS
|
Closed horizontal with a slightly clear vertical line, normal sound | C409 (394j) open | JKochem |