Cce Repair Tips

Search: cce
Results: 4816

Make	Model	Symptom	Problem	Solution	By
TV LCD CCE	TL360	Defect: inoperative	Checking the power supply output voltages on the connector terminals (cn401) I did not find the values marked there, checking the components on the power supply board I found d806 (sr510) shorted which killed the output power supply	Replacing it with another diode - with the same characteristics, the TV started working again.	bf.colatino
TV CCE	HPE14RD	Friends, this TV arrived at the workshop with the following defect: when I turn off the deflector it turns on normally, but when I turn it on	The TV's defect was the flash back.		bf.colatino
TV CCE	2918USP/AV	This TV had a 10cm dark band on the left and protection was working.	When searching, I found the c402 330pf /2kv damaged. After replacing it, the TV returned to normal.		bf.colatino
CCE	HPS 2991FS	Replace of the same	10v zener diode dz811 (shorted)	Replace of the same	julio almeida
CCE	DVD-757X	Off	C111 1000uf 16v	Replace	ELETROCLAUDIO AGUAS BELAS
CCE	HPS 2070V	No sound	Transistor q 403 shorted	Truck q 403 bc547	ROBSON FABIANO
CCE	TV2918USP/AV 1107283501	Dark band on the left	C 302 / 330pf broken		medeiros
CCE	HPS2071	Does not tune channels	33 volts are missing from the celetronic	Review, dz101 (33v), r106, r107, r108, r109 (all 12k)	johnny busnadiego
CCE	HPS 2002 E 2003	Retrace lines across the entire screen, the screen does not obey...	Fr- 901. tube plate.		Perse
CCE	HPS 2003	White stripe on the left side, characters at the top and bottom cut off, flickering in the image, noise as if it were being high.	Cap- 825, 47x160		Perse
TV CCE	HPS 2005	Tv cce mod hps 2005 which is missing colors, it had a problem with the ci 501 tda8841, after I replaced it it started working again, but now without color.	It was the micro capacitor in series with the palm crystal that was leaking and after the change it worked fine again	The NTSC crystal was also replaced, which was bad, I replaced it and I put it in altomatic mode, it is wonderful	BF.COLATNO
CCE	HPS 2092	Normal power supply, but does not oscillate	Causes broken capacitor 470x25v (c828)		arasonic
TV CCE	HPS 2185	When the image of the proclamation comes close to the screen, it becomes blurred. When reducing the contrast and brightness it becomes good	It was the fly bak's ground pin that I hadn't connected, because the k was previously not using this pin. Even so, it was a little yellowish, so I took the leap and discovered that reducing the abl speed to r 423 solved the problem.		BF.COLATINO
TV CCE	HPS3301	Device without image. The same came to me, stopped, and with the fly-back holed. After changing it, the TV came with audio, but without image and if I slightly accelerate the screen it appears. but when turning it off and on again the problem persists	The defect was in resistor r4 27 (12k) it was open on the abl line.		BF.COLATNO
TV CCE	HPS2997	I got this TV with a lot of problems...first it wouldn't turn on then I went and saw that the 8.2v power supply was dead so I found the audio circuit shorted and I changed it...now it turns on but the image is reddish and not tube because I changed it...I also changed the ci all related to red and the numk voltage of the red pins which should be +ou_ 140v is 40v I looked a lot on the tube plate and nothing	It was the tda 9573h/n3/a processor that was defective		BF.COLATNO
TV CCE	HPS 2991FS	This TV turns on and off and you can't take voltage measurements, I've already changed the BC's, capacitors and nothing.	It was the d410 diode with a leak, I replaced it and resolved it.		BF.COLATNO
TV CCE	HPS 141D	This TV suffered a fall that broke the back cover of the cabinet, just a vertical line, I changed the output and opened the image, but now the image is washed out, I have already resoldered the entire board including inside the varicap and nothing, I tested all the power supplys they are ok	It was the tube		BF.COLATNO
TV CCE	HPS 1402B	This cce hps1402b tv that doesn't allow adjustment, I already exchanged the flyback for a new one, it only gives the most sound because the fly is powering but the 12v power supplys don't come out	Defect resolved was the q401 shorted.		BF.COLATNO
TV CCE	HPS 2991	It doesn't turn on - it just gives the starting pulses, but it doesn't oscillate as it should. TV burned by lightning. I replaced 2 fets+ci oscillator+ resistors, diodes and I can't find anything else.	I changed the fets and everything was fine.		BF.COLATNO
TV CCE	HPS 1407	This TV arrived at my electronics with a burnt horizontal output. I exchanged it for the new one but I didn't find anything else faulty, it has normal voltages.	The bcs 337 of the power supply is defective.	Replaced and resolved.	BF.COLATNO