Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
TV CCE	HPS 2185	When the image of the proclamation comes close to the screen, it becomes blurred. When reducing the contrast and brightness it becomes good	It was the fly bak's ground pin that I hadn't connected, because the k was previously not using this pin. Even so, it was a little yellowish, so I took the leap and discovered that reducing the abl speed to r 423 solved the problem.		BF.COLATINO
TV CCE	HPS3301	Device without image. The same came to me, stopped, and with the fly-back holed. After changing it, the TV came with audio, but without image and if I slightly accelerate the screen it appears. but when turning it off and on again the problem persists	The defect was in resistor r4 27 (12k) it was open on the abl line.		BF.COLATNO
TV CCE	HPS2997	I got this TV with a lot of problems...first it wouldn't turn on then I went and saw that the 8.2v power supply was dead so I found the audio circuit shorted and I changed it...now it turns on but the image is reddish and not tube because I changed it...I also changed the ci all related to red and the numk voltage of the red pins which should be +ou_ 140v is 40v I looked a lot on the tube plate and nothing	It was the tda 9573h/n3/a processor that was defective		BF.COLATNO
TV CCE	HPS 2991FS	This TV turns on and off and you can't take voltage measurements, I've already changed the BC's, capacitors and nothing.	It was the d410 diode with a leak, I replaced it and resolved it.		BF.COLATNO
TV CCE	HPS 141D	This TV suffered a fall that broke the back cover of the cabinet, just a vertical line, I changed the output and opened the image, but now the image is washed out, I have already resoldered the entire board including inside the varicap and nothing, I tested all the power supplys they are ok	It was the tube		BF.COLATNO
TV CCE	HPS 1402B	This cce hps1402b tv that doesn't allow adjustment, I already exchanged the flyback for a new one, it only gives the most sound because the fly is powering but the 12v power supplys don't come out	Defect resolved was the q401 shorted.		BF.COLATNO
TV CCE	HPS 2991	It doesn't turn on - it just gives the starting pulses, but it doesn't oscillate as it should. TV burned by lightning. I replaced 2 fets+ci oscillator+ resistors, diodes and I can't find anything else.	I changed the fets and everything was fine.		BF.COLATNO
TV CCE	HPS 1407	This TV arrived at my electronics with a burnt horizontal output. I exchanged it for the new one but I didn't find anything else faulty, it has normal voltages.	The bcs 337 of the power supply is defective.	Replaced and resolved.	BF.COLATNO
CCE	HPS1470	Vertical closed	R301 1m8 open close to the a/v input (this resistor goes to the service switch)		simas433
TV CCE	HPS 2185	This one arrived with a short fly, I replaced it and it worked. However, it doesn't tune the channels. I measured the selector voltages, they are normal.	I managed to fix the TV, it was the nic selector. I changed it and it worked normally, the image was yellowish, I changed the abl r too.		BF.COLATNO
CCE	TV 29USP	Sem as (off as ok)	C662 1,2kpf smd		betoteck
CCE	1490C	With reduced screen retrace line	Deflector		domingos sp
CCE	HPS2197FS	It doesn't turn on, plugging it into the socket and removing it, the LED lights up, then the TV works normally, but turns off after a few minutes	Defective photocoupler	Photocoupler replacement	johnny busnadiego
TV CCE	HPS 2997 FS	Defect: turns on and then turns off, sometimes turns on with no sound or image	I rocked the ic 301 and the fr123. it started working normally again.		BF.COLATINO
TV CCE	HPS 1471	Defect: disarms the closed vertical protection	Solution: capacitor c107 (+ b of the selector) shorted		BF.COLATINO
CCE	HPS 2185FS	Press the power button LED blinks but does not turn on	In my case, I just adjusted the screen and it worked normally		SENPRETOR
CCE	HPS2044	Turns off immediately after turning on	Q802 e q804 - both bc337	Replace them for bd135	eletronicaapolo
CCE	TV 29 UPS	Inoperative power supply (zero volts)	Sudden power outage.c 422 560pf shorted.	Just replace it and that's it, the defect was fixed.	Raimundo
TV CCE	HPS2071	Turn on and off	There was no need to change the bcs 337.	Resolved with a general re-welding of the flyback pins, I noticed that the welds were oxidized.	BF.COLATINO
CCE	HPS-2991 FS	Vertical reduced to 4 image fingers at the bottom of the tube.	Capacitor c 311 leaking. in another case I found the resistor r 306 open.	I replaced them and the image was normalized.nivaldo rio das ostras.thank you!	NIVALDO