☰

Cce Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: cce
Results: 4824
Make Model Symptom Problem Solution By
CCE TVS2910FS
Turning off in a row 812 open diode klein
CCE HPS2081
Does not oscillate horizontally Vertical output Replace vertical output DIGITAL TEC
CCE HPS1471
Image interference and sound noise C102-smd Replace c102 smd CENTER SOM ELETRONICA
CCE HPS2906C
It doesn't turn on, it just flashes the LED, +b doesn't adjust, it varies even when the horizontal is turned off. Circuit reg. power supply r820 127kΩ open and d812 5v1 changed. Bruske
CCE HPS1491
Vertical closed from the middle up R303 (68k) open ARAUJO
CCE HPS 2092
??? 		When I turned on the TV, upper retraction lines appeared with a low horizontal range Burnt resistor r308 - problem solved after replacement FELIZ
CCE HPS 2991FS
Screen showing phase ghosting from left to middle of the screen Ceramic capacitor c 402 shorted and resistor r 401 burned, in the hsinc circuit Jose Fernando - Saquarema
CCE HPS 2997FS
Closed horizontal with a slightly clear vertical line, normal sound C409 (394j) open JKochem
CCE HPS2991
Dark band on the left side of the screen C402 331p x 2kv capacitor replaced Carlos Guerra
CCE HPS-2198AV OU 2185FS
Tv with the image with a blurred green outline if you enlarge the screen the image keeps blinking or when you turn on the image it shakes, replace the L402 filament coil with a 1r rejistor, don't decide to do a janper @@@ L402 coil replace with a 1r resistor ok A ELETRONICA ARNI-LEOBERTO LEAL-SC
CCE HPS2071
TV doesn't turn on, it only has power on the primary power supply Tea1533 replacelo KRAUSE
CCE HPS-2908
Normal power supply but when it comes out of stand-by it does not oscillate horizontally. with the test tip on the base of q400 it oscillated normally C-429 220pf/500v with small leak C-429 220pf/500v with leakage replace without measuring Rtg_28
CCE HPS2171FSI
Does not turn on (standby only) Drained c825 capacitor Replace c825 (47ux160v) with (47ux250v) cesar_unitec
CCE HPS-2908
Normal power supply but when it comes out of stand-by it does not oscillate horizontally R823 from 2k2 open dudi Benedito
CCE HPS 21AV
ESQ 		TV didn't turn on Vertical output la78040n after changing it, I show gordo ubatuba
CCE HPS 2171 E 2185
Thin black stripes on the screen C306 broken pin 17 of micro ic 101 Replace it (note how much you can fix it. It loosens one of the sides) antonio nobrega(patos pb)
CCE TVS 2910 FS
Does not tune in AV channels without audio Zenner dz 701 and 702 Replace Felex
CCE HPS-3301
HPS3301 		TV doesn't shoot the image, it just stays on the stand bay. It must be a power surge. I don't have it yet. Tatu
CCE HPS 2097
Does not arm the power supply voltage on pin 2 of the power supply ci with 10 volts where normal is 15 volts R 812 r 813 amended Replace them, pay attention to measuring them out of place as they work in parallel and can take time away from you. antonio nobrega(patos pb)
CCE HPS 1497
R113 heating up and killing the varicap's 5 volts C 107 fully shorted 470 uf 16 volts Replacelo antonio nobrega(patos pb)