Cce Repair Tips
Search: cce
Results: 4834
Results: 4834
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS 1470
1470 |
Strong buzzing at the power supply | I replaced the r804 with a 1k5 resistor | Resolved | ELETRO LUIS |
| CCE |
TV-29USP
|
Shaking image | Scrrem was very open | I just adjusted it and it was ok | paulo morato |
| CCE |
HPS2171
|
Image switching between plain screen or with image | R 205 (270 r smd)open or with cracked solder | Resolder or replace note; it is below the cf 201 | antonio nobrega(patos pb) |
| CCE |
HPS2197FS
|
Screen closed on both sides, when the image appears it triggers protection, it keeps turning on and off | Changed the capacitor c 825 solved | nicodemos aires ES | |
| CCE |
HPS-2002-2003-2004
|
It doesn't turn on, press the power LED turns off, press it again, it stays off @@@ | Change c835 it measures correctly in the test | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
| CCE |
HPS-2002-2003-2004
|
Does not turn on standby led off dead power supply no voltage @@@ | Diodo dz801 smd 18v e r802=1k5 smd | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
| CCE |
HPS1470Z
|
Won't start - fly moans - has +b | C733 470x35v short | Replace capacitor | matieski |
| CCE |
HPS2071
|
V doesn't tune in. all tensions ok. appears to be seletronic with defect | C102 smd 102 | Replace c 102 smd / you can put ceramic in place | tecnardi |
| CCE |
HPS-2181
|
Doesn't work. | Secondary power supply of 120 volts and 18 volts showing zero. | Solution: r 807 (56r), r829 (330r), r833 (56r). | Nedson |
| CCE |
HPS-3407 FS
|
Activating protection. | Change without measuring q802, q805, c834, c835 and c836. | FERNANDO S | |
| CCE |
HPS-1402 B
|
Burning horizontal outlet | C415 4.7 160v | Replace for a new one ok | ELETRONICA BIANCA IPIRÁ BA |
| CCE |
HPS 2185FS
|
Horizontal does not oscillate, i.e. the TV does not turn on, it just remains on standby. | Faulty sound output ci | Replace ic 601 | AFONSO SANTANA |
| CCE |
HPS 2071
|
Turns on and then turns off, screen blurred 12v power supply at zero | Q802 changed between collector and emitter | Replace q802 | AFONSO SANTANA |
| CCE |
HPS 1407
|
The TV turns on only with the stand-by LED on and with a high power supply of around 150v. | High power supply ic 802 and dz 805de 4v7 faulty, does not connect open transistor q802 between base and collector. | Replace all damaged components and the TV works normally again. | AFONSO SANTANA |
| CCE |
HPS-2002-2003-2004
|
Does not turn on stand-bay led off without b+ ov @@@ | Just change the c812=47ufx25v | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
| CCE |
HPS1403
34B1 |
Inoperative (led does not light) | Change c807 or c805 open | beto eletronica | |
| CCE |
2971N
|
This TV arrived here without generating it, it turned on the stand bay but it didn't arm, I measured the voltages and I suspected the capacitor c 826 as it didn't accumulate anything, I removed it from its place and it was dead | Replace capacitor c 826 470mf 400v | moroni eletronica | |
| CCE |
HPS 1471
14" |
On, off, vertical closed | Dead or low 8v line | 8v line regulator q804 (bc337) it is also possible to replace the q802 (reg. 3v3) | Miojex |
| CCE |
TV2118USP/AV
SL23-1 |
The TV turns off after a few minutes of being on | Q802/q804 transistors | Replace for bd 135 | MARCELO FLACH (ELETRONICA CENTRAL) |
| CCE |
TVD2901
|
TV doesn't turn on, stays on stand-by | There is no oscillation...cause it was a horizontal output, measure the tension in the collector there is tension, measuring it seems to be in place...but you have to remove it from the place to measure, because it is with the driver...I measured it in short... | Replace q402 - bu-2520dx |