Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS2071	Catches some channels, others don't	More than 33 volts is normal and more than 5 volts is normal	Replace the channel selector	eletronica arthur
CCE	TVS 2910FS	Nor 51 volts	Q902 q905		juci
CCE	HPS2071	Turns on and image appears and then turns off	Micro pros. defective	Replace	Eletroclaudio Aguas Belas PE
CCE	2185FS	Does not tune the channels due to lack of +5v.	C 629 this guy is smd value 10n without it it works		luiz gonzaga da silva
TV CCE	HPS2971FSG	Vertical closed	Only one horizontal line, causes open fr423-10r	Replaced and resolved.	BF.COLATINO
CCE	HPS 1473 1474 2071 2073 2074 2076 2976 2982 2983 2991 2912G	Turning off by itself	Protection line there are defects also found in the protection line at pin34 of the microprocessor to check if there is a defect on this line, just remove the transistors k403 and k404, turn on the device and check if it has stopped turning off, if so, do a scan of this entire line looking for components with cold sound defect and cracked component in the protection line and it is a good idea to scan the entire PC		etronica arthur
CCE	TVD2901	Turning off by itself	Change photo coupler more		eletrnica arthur
CCE	HPS2071	Intermittent or hissing audio without video characters dropping out if you don't tune in to all channels on your own	Whenever they have defects related to these items, they must remember		eletronica arthur
CCE	HPS-2071 34BI	Totally inoperative, standy by off.	Ic 101 (tda 9570h) in Curto.tv did not turn on, there was no standby indication.	After replacing the ic 101 (tda9570), the device was ok.	clayton
CCE	HPS2971	Dull blurry image	C213 10n /50v on pin54 of ic101 and r441 4k7 everything on the abl line takes + or less 15 days to find this defect..	Replace without testing..	Elias2305
CCE	HPS2007	Dead	Standby led d flashes and does not start, + b normal.	Transistor drive replaced, it's good to remember that the +b of this TV is 128v and not 103v, but it's only the one with the letter c. at the end	BF.COLATINO
CCE	HPS 2070S	Doesn't start	Exit time. Shorted, replaced, checked all voltages when turned on, in 03 seconds it burned out again.	After checking better, I found the s driver transistor. horizontal short from base to emitter.	BF.COLATINO
CCE	HPS-2991FS	Arming and disarming directly, there is no time to take measurements	Ci 601, tda7496s, shorted audio amplifier.	Replace without testing, c659 and c660 of 1000μF/16v.	BF.COLATINO
CCE	HPS-1402B	Normal sound, no image, filament does not light up, no horizontal noise.	Fr401 open (+b power line to flyback). After replacing this resistor, the TV started working normally again.		Paulo - São Luís/MA
TV CCE	HPS 14-E	It worked normally for approximately 20 minutes and then turned off,	It was resolved with several cold solders, including on pin 1 of the flyback.		BF.COLATINO
CCE	TV-20BLK	Doesn't start	Fet q801- k1611 shorted sub. by k1118, the standby LED turned on, but it didn't work	So I resoldered the fr401 and the problem was resolved.	BF.COLATINO
CCE	TVS-2910FS	Does not turn on, LED does not light, power supply is zero	Capacitor da power supply 470mf/385v seco.	Just replace it and that's it. The TV is complete.	CARLOS
CCE	HPS2988	Vertical closed even when placing another	D410 open	Replace measure outside the plate!	asbrito
TV CCE	HPS 2185SF	Increase and decrease volume turn off change channel	Change all touch switches on the front panel		leonardo souza costa
CCE	HPS-2971	When the frame increases in volume on the sides, it starts to sway	Photo coupler with leak between pins 1 and 2, and the transistor shorted smd q808	Replace of photo coupler ic803, and q808, zener dz811....	house eletronica ltda