Search: cce
Results: 4816
Make Model Symptom Problem Solution By
CCE TVS 2910
Doesn't start C825, c408 HP ELETRONICA
CCE HPS 2171 FS
Turning off by itself!! Solda fria no fly back!! Perse
CCE HPS1471
Power supply disarming!! T 802 e 804 Perse
CCE HPS2080
Tunes channels with a lot of drizzle and a loud whistle (appearing to be an off-frequency oscillator) The drizzle was caused by the open r101 (8k2) that feeds the cag and the whistle by r 402(10r) that feeds the +b of the flayback Replace r101 from 8k2 and r402 from 10r fernandocamarques
CCE HPS2073
LED flashes several times and does not turn on Tube socket,q 804,c825,c 829,c805 HP ELETRONICA
CCE HPS1401H
Doesn't work: Turning on the TV, we saw the fly smoking. We changed the fly, and turning on the TV to the 190w series, the lamps kept turning on and off. Putting our thumb on the fr 402 1r, -12v fusistor of the vcc on the vertical line, it was hot ic301 tda9309 was shorted. Replaced, the fly, and the ic301 tda 9309 the tv returned to normal. lucas40
CCE HPS2185 FS
TV won't turn on power supply between 70v and 100v Capacitor loss of capacity C 825 +b power supply replace put 100mf 160v This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE HPS2171
When turning it on, it worked, after a minute a noise appeared on the screen accompanied by noise in the flyback, which made me think it was bad. D813 with a small leak, and only when it warmed up, the cold was perfectly normal. After the exchange it worked perfectly. Leônidas (Léo) Natal RN (This email address is being protected from spambots. You need JavaScript enabled to view it.)
CCE HPS 2185FS
Normal, more horizontal power supply does not oscillate, therefore the TV does not turn on Faulty sound output ci Replace ci, tv works normally afonso Taquari Eletronica
CCE HPS-21STP
TV doesn't turn on, the LED lights up normally when you press the button, the LED turns off the relay 3 times and stops, and the LED keeps blinking constantly Varicap killing at 5v voltage Replace the varicap Eletroclaudio Aguas Belas PE
CCE TV2118USP
Image shifted to the right side with aliasing C417 amended Replace it without measuring ANTONIO NOBREGA(PATOS PB)
CCE HPS-2971 N
Volume + is activated, it does not stabilize, it returns to minimum. Micro volume switch -, replace it, even if it is perfect in the test, it is ok. Cláudio Ribeiro, TECNOSAT ELETRÔNICA E INFORMÁTICA, JATAÍ-GO, This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE HPS1471
34L
No audio via av: R651 2k2 smd aberta. lucas40
CCE HPS-2005
When placed in the socket, the LED on the panel lights up, pressing the power button turns off the LED and nothing works; measuring the tensions are all correct but it does not generate high tension It took me a while but I managed to find the defect, just replace the c410, if you get a vibration-like noise, replace the c829 HEMERSON ELETRONICA MM
CCE HPS2008
Does not turn on normal power supply LED off Lack of power supply to the computer on pin 74 klein
CCE HPS-2991
HPS 29
Bad image, difficult to adjust screen L400 shock on the filament line, place jumper
CCE HPS-2991
HPS29
LED blinks but does not turn on the TV Resolved diode d410 paulo eletronica
CCE HPS2004B
LED off TV inoperative Open 27k resistor r801 Eletroclaudio Aguas Belas PE
CCE HPS1450RS
TV has no sound and a line in the center of the screen in a horizontal direction, that is, with the vertical closed. Defect in the 16.5 volt power supply, this voltage did not exist. Just fix the power supply and it's back to normal. Armando da eletronica só tv.
CCE HPS1450RS
TV stopped due to high voltage leak in the fly-back screen. Due to the tension of the fly-back screen jumping to the hot ground (chassis) it causes defects in several components (see). Replace fly-back, holey, see also, r416=1k, toast, see, d240, d205, d242 all signal diode=in4148, see also r241=68k, and if the TV doesn't work, also replace the c i - croma=ka2154 ai it is resolved.....uuuuμFa!!!. Armando da eletrônica só tv.