Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS2071 2071	Dead power supply	R801 dz18v		dedesom
CCE	HPS-2090F/2070	Stripes looking like screen with audio	D580 open	Replace d580 1n4148	beto2828
CCE	2199 2199	When turned on, it arms and returns to stand by	Capacitor c825	Replace 47 mf 160	itan (cabeça)
CCE	HPS-1490E	Turn on the sound is low and noisy even if you turn it up it stays low	Change c663 was swollen and ic 601 is normal		Eronaldo
CCE	2071	Power supply does not oscillate	Nano capacitor shorted near tea 1533
CCE	HPS2985	Doesn't work	R816 open	The stand by LED lights up but when we activate power the TV does not work. Checking the power supply I noticed that it was high with 175 volts and that the power supply was emitting a clicking noise. Measuring the components I found the r816 open	GILSCE
CCE	HPS2197S	When I turned on the TV, there was no image or sound and the stand by was flashing.	I changed all the power supply capacitors and nothing, then I decided to change the flayback and the TV worked perfectly again		dinho27
CCE	HPS1471	Does not turn on, has all normal power supplies	Cristal do micro x701	Help yourself, leave your tip.ass. josé	ELETRONICA ARNI- L. LEAL/SC
CCE	HPS2070 A/B	Does not turn on, 103v supply with 18v	C808, c829, c825 sold out		calixservice
CCE	HPS-2997 FS	Device without horizontal scanning, just a thin strip in the center of the screen, vertically.	Polyester capacitor, c- 409, value: 394 j x 250 v. Totally out of capacity, replace it, it's ok.		Cláudio Ribeiro, TECNOSAT ELETÔNICA E INFORMÁTICA, JATAÍ-GO, This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	33R	Image blinking (as if it were going to turn off)	R423		HP ELETRONICA
CCE	HPS141B	Does not oscillate, does not come out of standby	Voltage on the driver 104v, when turned on it drops to 12v. cause t401 (horizontal output driver transfer had 150r impedance, replaced with one with 100r, it oscillated again.		LUIR
CCE	2908	Completely dark screen	Defective abl	Follow the abl trail you will see a 1n4148 diode, take it out, in my case, the TV is working very well without it	fofao
CCE	HPS 2991	TV with the image all red	R423	I replaced it, it's new	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS 1470Q	No characters	R427, 4k7 open	Replace the same	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS 2971	Burning power supply fets, even after changing everything	Fake p6nk90z fets sold on the electronic market	Replace them for originals even if they are scrap	Manoel
CCE	1470AP	Changed fly back disappeared av	Yarn wrapped in inverted fly back.
CCE	HPS2985	When switching on before the screen reaches full brightness, some vertical colored bands appear at the top of the screen, after the brightness normalizes the screen has the image sliced horizontally (stripes cover the entire screen).	This defect is caused by the open 150 r resistor r310, next to the yoke wires (near the vertical output and the deflector wires) just replace it.		WAGGUINHO
CCE	HPS2081 OU 1481 1481	It turned on after 5 or 8 minutes after activating power	D401ed705 leaky 1n4148 diodes.		dedesom
CCE	HPS-2091	The television turns on and after a few seconds it turns off, especially in white images, because the x-ray voltage changes and the TV turns off..	R 843 amended	Changing the resistor 0.68 to 0.22...	house eletrônica ltda