Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HHPS-2185 FSB	When the LED turns on, it flashes 11 times and the screen appears with both sides closed about 4 centimeters and turning off	47uf 160v capacitor c825 burst and cold soldering on the fly back pins	Replace o capacitor e resoldar o fly back	eletroclaudio aguas belas
CCE	VARIOS	Turning off	Exchange of transistors bc337 and bc 327		Sergio Luiz
CCE	HPS3301	Image without definition	R.423 1k		julio itaguai
CCE	HPS2991		Screen does not turn on. voltages ok, filament ok. television apparently in operation.	C901 on PCI kinescope on the run....	py3ig
CCE	HPS2185FS	TV didn't work stand-by LED blinking I changed it	I replaced q802, q803, q804 and fr401 1r-1w, but unfortunately the output burned out instantly so I changed the output capacitors c645, c646, c639 and c641 and then the tda 1517 and the TV started working 100% again		ZANELA
CCE	HPS 2991FS *	It doesn't work, I replaced the complete board with another tube, I turned it on but it didn't work, I was worried because the other board wasn't defective, then I checked the normal voltages, I put it back on, I adjusted the flay back and it worked normally.	Adjust the screen.	Adjustment	wagner
CCE	HPS-2007E	It saturates the screen, (flashing) like the image in the background	22r fr901,trc plate		Eletronica Benedito
CCE	HPS1402B	It doesn't turn on, only the standby light is on.	This TV only had the standby light on, when pressing the power key the light went off but the TV did not turn on, be careful when testing components, because when measuring the capacitor c812 47uf x 25v on the capacimeter it gave 42.1uf a value that was even close the correct value, but guess what, that capacitor was the villain in the story, just put a new one in and solve the problem.		FERNANDO
CCE	HPS-2097 *	Doesn't work and power supply blows fuse	Dz 801 insurto	Your replace of the same value but higher in watts.	wagner
CCE	HPS2971C	Image darkened and became mute	After checking that the kinescope filament was lit, I replaced the 4k7 r435 of the abl that was altered, and after checking the flyback I found through the diagram that the coil that goes from pin 9 to pins 1 and 2 was open, I changed them and everything OK.		MRinformática
CCE	HPS1497	Power supply + b 103v low and varying the value	Trafo t 801		ELETRONICA ROBSON (DEBIQUE)
CCE	HPS 1407F		Ci tl431 r816 113k-obs:replace q802 bc337 nem measure		MARCOS UBATUBA SP
CCE	HPS1471	Blinking LED does not turn on	Q802 broken even good in the test	Replace for one of the same good luck	Evaldo Eletrônica gomes Uruçui-Pi
CCE	HPS-1402	Channels with block user "does not remember password"	Put the TV in standby mode and press the following p.ch button on the control. for 2 seconds), OSD key (one touch), mute key (one touch), sleep key (keep pressed until the TV turns on). obs. unlocks several models	Help yourself leave your tip	ELETRONICA ARNI-LEOBERTO LEAL /SC
CCE	HPS 2030		C 852 exhausted, str pin b		franco@tatui
CCE	HPS21AVP	Blurred image of adjustment in scrim	L 402 remove and place a resistor of one (r) in place		MULTSOM
CCE	HPS-2071	No image normal sound dark screen. filament does not light up	Change the tube		eletroclaudio aguas belas
CCE	HPS1481	Loses flashing color	Exchange the two crests 501 503		julio itaguai
CCE	HPS	When changing channels, sometimes it changes normally if the channels go through, sometimes only channel 0 remains.	Eeprom memory 80021		Fernando
CCE	HPS 2997	Disarms immediately after being turned on	Capacitor eletrolitico 100x160v	Replace without measuring as it misleads when checking	ARASONIC