Cce Repair Tips
Search: cce
Results: 4824
Results: 4824
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS-2007
|
When turning on, the stand-by LED flashes but the TV does not start. | Replacement of c812 (electrolytic capacitor - 47uf x 25v) | ||
| CCE |
HPS 21 AVP
|
The TV didn't oscillate, there was an oscillating noise, the power supply was normal, the LED was on but the TV wouldn't start. | Bad contact at ioc, the famous person does everything. | I just desoldered it with hot air and it was beautiful. | Armando da eletronica só tv. |
| CCE |
HPS 21 AVP
|
Does not tune to any channel and only drizzle on the screen. | Causes eeprom (memory). | Just replaced it and it was ok. | Armando da Eletronica Só TV |
| CCE |
HPS2091/OU 20BLK-BLUESKY
|
It just stays on standby and doesn't turn on | I replaced the c825 (47/250) and nothing...checking the voltages on the computer I noticed a voltage fault, I replaced the c 722 without measuring...everything worked again. | A small leak on the c722 (220k disk) | vagnernardes |
| CCE |
HPS-2971 C
|
Turns on normally but there is no image heating up r407 defect c409 open 564k | Heating up r407 defect c409 open 564k | Put c 409 of 400 v | luiztvsom |
| CCE |
HPS 2988
|
Vertical closed (even if replaced) | Check diode d405 for short or resistor fr419 | This line starts from pin 4 (flayback).. the 1n 4148 diode corresponds to the line that takes the 13 volts to the vertical | DRBOOT |
| CCE |
2070
COM CI LA 7680 |
Vertical closed | Ic 802 (7809) | HP ELETRONICA | |
| CCE |
HPS2988
|
Power supply does not arm (tic tac on chopper) LED flashing | Remove the release from pin 1 of the flayback, if the power supply returns to normal, the capacitor c406 = 330 pf will be shorted or leaked | Note; the capacitor, in the event of a breakdown, does not allow the horizontal to oscillate, causing the trafo (chopper) to emit such a tic tac (pulse) along with the standbay LED - due to protection of the power supply circuit | DRBOOT |
| CCE |
HPS-1491
|
Oscillates and cuts the stand by turns off and lights up on the same shelf | Shorted deflector | Replace | eletroclaudio aguas belas |
| CCE |
HPS1471
|
Does not tune channels | R109 12k changed on pin 1 line of cn401a | 12k resistor replacement | Robson correa |
| CCE |
HPS-1407
|
A bar on the left part of the screen | R414 10k proximo ao flay back | fabiusmax | |
| CCE |
MD2400
|
Output ok but there is no sound in the speakers | Ic501(reg.7809 open) | Replacelo | ANTONIO NOBREGA(PATOS PB) |
| CCE |
HPS3301
|
Image shaking as if it were a fountain | If this defect appears after you changed the r t 437 of the abl because the image was blurred | Replace the r435 smd that is in series with the d 402 that comes out of the abl and goes to the micro pin. If this tip helped you, don't be selfish, let yours be happy too and if you want, you can deposit some money in my account lol | itan (cabeça) |
| CCE |
HPS2997FS
|
Delay for image to appear | Tube filament inductor | It was just a matter of changing. | JUVENCIO |
| CCE |
HPS1402
|
Image with 3 colors and out of focus | Ver r403 1hom e replace ci vertical | johnny busnadiego | |
| CCE |
HPS 2971
|
Turn on and off | Q 802 q 805 bc 337 change without measuring | ||
| CCE |
TV-29USP
|
With retraction lines (return) across the entire screen | Disarming too | Replace the fr 901 resistor and the kinescope (imaging tube) | lele |
| CCE |
HPS 2071
|
Doesn't start | Socket | fabiusmax | |
| CCE |
DVD-750X
|
Calls then doesn't call | Processing board | 2 diodes in4007 processing board | NEU 2010 |
| CCE |
HPS-33R
|
Blue blurred image | R916 | This resistor is located on the kinescope PCI, replace it | CSOM-(066)34231060 |