Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS-2991FS	TV turns on and after a few seconds, turns off by itself	Q802 and q805, both defective	Replace them and good luck!!!!!	EDUARDO
TV CCE	HPS2706	Burning horizontal output without heating it	C409 1n2k100	C 419 100v1μF	sinezio libano
CCE	TVS2910FS	Lack of horizontal width	Replacement of capacitor c407 value 3.3kpf/1.6kv		NILTON-AVARÉ
CCE	HPS-2185FS	The filament lights up but no image appears and the LED keeps blinking	Screen atesion does not have the tube shorted	I removed the plate from the tube and removed the glue that is between the pins of the tube barrel and cleaned the short and the TV works fine ok	eletroclaudio aguas belas
CCE	HPS 2071	It turned on and off immediately with the upright closed after fixing the upright, it all came with retrace lines	Change q 802 and q804 both, bc337/25 the vertical closed was because of the shorted audio output, tda1517 because their power supply is the same and the retrace lines the fr901, 220r to test the vertical and not buy a new one later To exchange q 802 and q 804, remove the ci from the audio output and turn on the device	Replace audio output q 802 q 804 fr 901	Marcio
CCE	HPS1471	It doesn't turn on, the LED just keeps blinking	(q802	Replace the same	hildon
CCE	21US	No power supply	When you plug it into the socket you only hear a little grating noise, change the ci smd 801, tda1533at, check the fet 2sk3599, good luck		DELEGADO
CCE	2971	Doesn't start. The LED just flashes 3 times after it stays on	After checking all voltages, it was found that the 8v6 line was low	Tda9855 shorted. After changing it, it worked..thankful for the tips from colleagues here on the forum.	nois
CCE	HPS2185FS	Horizontal does not oscillate	47uf/160v capacitor, in the +b line with little capacitance or high esr	Replace capacitor	taquari eletronica
CCE	HPS2185FS	TV doesn't work, capacitor c825=47uf for 160 volts buxudo	Put another value in its place, modification	100μF capacitor was placed for 160volts and it was ok	This email address is being protected from spambots. You need JavaScript enabled to view it.
SOM CCE	MD-2400	The unit throws the laser but the motor turns the wrong way to the left	Resolder the smd board under the table, check the keys and check the flat of the unit if it is not burned	Help yourself leave your tip	ELETRONICA ARNI-LEOBERTO LEAL /SC
CCE	2910 FSD	Turns on and then turns off (arming protection)	Q802 e q805 (bc 33725)		Carlos Carbonari
CCE	HPS2991	Filament lights up, has high voltage but no image	Flyback with broken screen potentiometer	Changing the flat	ZEZINHO
CCE	HPS 2997 FS	Dark screen without screen	C 901 of 1kpf/2kv on the trc board		MACCELETRONICA
CCE	HPS1471 34B1	Losing tune after a few minutes does not memorize channels or menu settings	Deficient data clock circuit on the SCL and SDA line directly touching dz 701 and dz 702, both 5v6.		Derailton
CCE	HPS2185	Turns on and then turns off.	Flay	Replacement	This email address is being protected from spambots. You need JavaScript enabled to view it.(floripasc)
CCE	HPS-1402B	Without image and with normal sound, the image only appears when it is willing. It's soft	Transistor q401 defective from base to collector	Replace the same	eletroclaudio aguas belas
CCE	HPS2971N	After changing the flay-beck the sound was as if it was going out of tune	Surface 1, R423	Review circ. abl	DANIEL SOLÂNEA PB
CCE	HPS2003	Power supply pulsing, looks like shorted fly back	C423 4.7uf for 250volts shorted, 180v power supply from rgb		HP ELETRONICA
CCE	HPS2910	Sides closing	Eeprom deprogrammed	Ground pin 78 of the micro and adjust the width	ANTONIO NOBREGA [PATOS.PB]