Cce Repair Tips

Search: cce
Results: 4816

Make	Model	Symptom	Problem	Solution	By
CCE	HPS 1471	Vertical works only the bottom half	D301	D301	DIGITAL TEC
CCE	2118 14	TV turns on and off with half the image closed	Ceramic condenser that goes on the deflector pin	I replaced it, it was 3312kv, it was black	negodrama
CCE	HPS2971	TV doesn't work, just lights up on standby (flashing)	Q806 (smd) shorted		This email address is being protected from spambots. You need JavaScript enabled to view it. Bruno Nicacio
CCE	HPS2907 FS	Vertical dash on the screen	C409 , 394j 250v	Barter it	This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI
CCE	HPS-2185FS	When turned on, the LED flashes and the relay activates	Fly back com screen alto	After racking my brains and changing several components without results, I adjusted the fly back screen. Finally the LED stopped blinking.	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS 2092	Not starting	Cap.33.160v. e cap 47.160v	Replace the same	fernando ferreira
CCE	HPS2071	Right side black belt	0r22 resistor r813 with changed value	Replace the same	rafael pantoja ig-miri
CCE	HPS1415	Horizontal line in the center of the screen, i.e. closed vertical.	Ic301=an5512 or ka2131 the shorted equivalent, with the short the r420=1r opens and to be sure if the ci is shorted, clean pin 4 of the ci with the sucker, if the voltage normalizes, replace it.	The ci an5512 and r420=1 r were replaced, and it was... ok.	Armando Olímpia.
CCE	HPS1401 H	Only the vhf signal comes in, that is, no uhf signal comes in.	Causes defect in ic101=33v zener.	It gave the impression that it was a defect in the varicap, but the zener was replaced and everything was... ok.	Armando da Eletronica S´Tv, Olímpia Est:de São Paulo.
CCE	HPS1403B	Dead power supply	Open 27k resistor r801		Eletroclaudio Aguas Belas PE
CCE	HPS2118	It doesn't turn on, it just hits the relay and it doesn't stay on, +b ok	C417 with leak		Bruske
PHILIPS,CCE,SONY	VALIDO PARA AS MESMAS		TVs turn off so quickly that we have no idea where to look for the defect, here are some tips. You will use 3 diodes in4148, connect the anodes to the connector that comes from the main board to the tube board pin1,2,3 and join the cathodes and connect to pin 5, ready, the TV will no longer turn off, you will see the corresponding defect on the screen. This applies to the brands: Philips, CCE, Sony. In the case of Sony, we use 1k by 1/4W resistors, we connect each one to the RGB resistors We join the 3 ends and solder them to the connection, cool, in case the TV turns off so quickly that we have no idea, as already explained where the defect is, this tactic will release the plot faster on the screen, generally it takes 10s to release it, we reduce it to 4s You will use an 800m 6+6 transformer, connect it to the filament, wait for the cathodes to heat up and turn on the TV. There will be a way for you to access the error code and view the plot. There is a way for you to view the corresponding defect on the screen or how to access the error code. ex:0 0 0 0 0 how is 0 0 0 0 0 it means that the TV is working correctly if a number appears it is a sign that the TV is defective in another stage, the error code counts from left to right ex: 9 0 0 0 0 this 9 points to the eeprom memory or it is defective or lost or even a lack of power. a 10k resistor in the case of sdam1 sdam2 connect a short circuit from one to the other and turn on the TV when it starts remove the short immediately the TV will turn on in service mode this is either without the TV's CR or the TV is not turning on alone The LED turns on and the LED indicates the error code, eg: 9 blinks correspond to an error.		Miltom eletronica micro e epron
CCE	HPS-1473	With rainbow-shaped screen	It was the open 1r fro403		Eletroclaudio Aguas Belas PE
CCE	HPS-1473	TV without picture with lines of retrace normal sound	R 901 open on the oscilloscope board		Eletroclaudio Aguas Belas PE
CCE	HPS 2004	Power supply voltage + b was low, stand by LED does not light up	Replace capacitor 812 47x25	C 812	ELETRONICA ROBSON(DEBIQUE)
CCE	HPS2991 FS	Vertical closed (TV turns on and off)	Q804; q802	Replace the transistors without measuring, because in the static test it looks good	julio cesar (on line eletronica)
CCE	HPS2005	Low power supply 86v and reduced frame	Capacitor c 812 low capacity	C812	macceletronica
CCE	TV-2918UPS/78	Spot on the right side of the screen from top to bottom (horizontal)	C405(ceramic)(next to the socket that connects the york)	Replace c405(ceramic)	Jarbas Santos (eletro-serv)
CCE	HPS 2073	Retrace lines	R 901 open on the oscilloscope board	R901	H.IM ELETRONICA
CCE	HPS21AVP	Lack of width and turning off	Chap. c825 out of stock		klein