Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS2991	Turns off after a few minutes	Q802 and q805 are bc337	Replace the 2 trans. bc337 for 2 bd135	eletronicaapolo
CCE	HPS2991	Power supply does not break	C806	Replace the same	eletronicaapolo
CCE	HPS 2991FS CN 701A	Dark screen with sound	Check the blk curr in the everything socket (cn501) pin 5 must have 7v check the zener if it is good disconnect pins 5 of the tda 6106 the voltage will rise, replace the three tda	Replace the tda 6106 the three	Eletrônica Ômega
CCE	HPS-2991P	TV works normally but with a two-finger bar on the left side of the screen	Capacitor c402 close to the deflector socket, do not measure to change, c331pf/2k		fabiusmax
CCE	HPS1481	Does not start, STBY LED is on, secondary voltages are zero.	R832 (470k/ 1/8) aberto.	Replace and run for the hug.	Altevirlima (Valparaíso Eletrônica)PA
CCE	TV 29USP	Image shifted to/right	C 402 -330pf- 2kv		betoteck
CCE	TV-21US	Bu2502 dx burned out when replaced it heats up a lot image gets reduced frame	Change c418		the__troop
CCE	HPS 2976	Does not oscillate (does not turn on) LED lights up all the time	Even pressing the on/off button nothing happened, just the LED was on all the time. the flyback windings were internally open.	Flyback replacement	fabio3749
CCE	HPS 2976	Does not oscillate (does not turn on) LED lights up all the time	Even pressing the on/off button nothing happened, just the LED was on all the time. the windings		fabio3749
CCE	HPS21	Standby LED turning on and off	Electrolic capacitor c825	Replaced, returned to normal.	miguelito
CCE	HPS2991	Turns on, but no image and no sound +b ok	Pci do tubo		Bruske
CCE	HPS-2185	Does not turn on - LED blinking	In tda1517	Replace of ci tda1517 (audio)	Rubens
CCE	HPS 2097	Inoperative, LED does not light.	Zener diode that is on the power supply line of the power supply IC with leakage	Zd801 replacement	fabio3749
CCE	HPS1405	The LED lights up but doesn't turn on	Tda8841 processor (located on the ic501 board)	Replace	CASA DAS ANTENAS MACHADIN
CCE	HPS 21	There was no blinking LED image	This TV arrived here without an image with all normal voltages abl line ok 180v capacitor ok but it didn't work check the transistors on the cn 401 b board everything ok then I found the capacitor c 909 defective killing the signal	Replace c 909 on cn 401 b board	moroni eletronica
CCE	HPS 2971	It turns on, right after hitting it, comes on high and turns off after +or- 3 seconds	I thought it was ci 301 (vertical) but it was the open q802 and q805	I replaced the two (q802 and q805) and resoldered some soldering points that had bad contact and everything was resolved!	eliandro rato
CCE	HPS 2971	No sound, it seemed like there was mute, but there was no voltage and there was no audio signal, dead!!	Defect in tda 9855	Replaced the ci 803 and the audio returned completely normal	eliandro rato
CCE	HPS 2991	Turns on and off at the same time, the other TV didn't even turn on, it was just on stand by	Friends had two TVs with the same problem and different symptoms	C 160v 47μF	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	TV21US	Won't turn on LED keeps flashing	Solda fria no flyback		Eletroclaudio Aguas Belas PE
TV CCE	2185	When changing the flayback, the image gave the impression that the kinescope was exhausted. Pay attention to the direction of rotation if the filam does not light up. invert	Peba flayback low amperage		leonardo souza costa