Cce Repair Tips
Search: cce
Results: 4834
Results: 4834
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
HPS 1403
|
After the image appears, it turns on and off | Verificar transistor q802 (bc337) | ||
CCE |
HPS2003
|
Takes 10 to 15 seconds. the image appears | Fly back. | ||
CCE |
HPS 1470
|
It works for a few minutes and drops to number 1 and keeps changing 1-cleared several times until it stops completely and no longer obeys the commands | The defect was the power switch changing to 1m of resistance, it's soft! Sometimes it returned to normal, without any resistance and sometimes it measured high resistance. I left the meter hanging on it and watched the value fluctuate. that was awesome!!! | ||
CCE |
HPS14R
|
Vertical closed almost completely and the horizontal a little, about 5cm on each side | D201(1n4002) bad, killing the 8vcc on pin 10 of the ci tda8361. | ||
CCE |
HPS-1480D
|
Expanded image | The fly ferrite wire inverted "loop". r301 of 2m7 open | ||
CCE |
HPS 2071 OU OUTROS
|
The power supply starts and turns off soon after | Q802 changed. (To find out if the defect is a power supply, do the following | Short circuit the collector with the emitter of q807 “smd” you have to stabilize the power supply at 103v, if this does not happen, the defect is actually in the power supply. | |
CCE |
HPS 2981
|
Stop and the stand-by LED is on | Damaged flyback | ||
CCE |
HPS2081D
|
The on/off button does not work, it only turns on via the master button. The varicap doesn't work, leaving the blue screen (selector stopped) and thus remaining silent | Dz 813 shorted. | ||
CCE |
HPS-1402
|
Does not tune to all channels | 33v zener shorted | ||
CCE |
HPS14R
|
No characters appear | Resolder the ic701 and pin 25,26 and 27 components, check r717 2k2, check the coil around the flyback, it must have 5 turns. | ||
CCE |
HPS-2071
|
Image losing horizontal synchronization only at the top | Replace c404 with 4v7 | ||
CCE |
HPS-2706
|
Black line horizontally | R306 | ||
CCE |
2171
|
Hoarse sound | Alter r113 to 10r | ||
CCE |
2991
|
50v com 18v | Q409 | ||
CCE |
HPS-2971
|
Noise in audio | C671 | ||
CCE |
HPS2971
|
Hoarse sound | Alter r113 to 10r | ||
CCE |
VCR 90X
|
Device does not turn on | Display indicating the presence of tape in the compartment, accepts tape normally. This occurs because the video is programmed with a timer. When you eject the tape, you will see a clock symbol appear on the display. procedure: connect the power cable; place a virgin ribbon or one with the seal intact; press the time rec key on the remote control; the video will turn on; press menu...program... and delete them all using the reset button on the remote control; | ||
CCE |
VCR 90X
|
Display completely off or clock after making the adjustment does not change | Procedure: reset the device plug the device into the socket press the power key to turn on the device short circuit momentarily short pin 10 (by) of the ic901 located on the front panel to ground (the device will turn off) turn the device on again by pressing the power key follow the general procedures to adjust the clock. | ||
CCE |
SS9600, SS9900 E MD2400
|
Does not tune to FM stations above 107.7 MHz | When you receive any of these models for repair, which does not tune into a local station above the 107.7MHz frequency (e.g.: 107.9MHz), just replace the IC 401 (micro) with the new IC code 710100057 for the SS9600 model. or 710100037 for models ss9900 / md2400. Attention: - This replacement is specific to cases in which the radio does not tune in to a specific local station above 107.7 MHz. for any other type of problem related to the micro (ic 401), use the ic code 710100007 for the ss9600 model or 710100034 for the ss9900 / md2400 models. | ||
CCE |
CM 260CD
|
Does not accept the disc (ejecting the cd) | In this car radio model with CD, when it occurs that when inserting the disc into the compartment it is automatically ejected, the fault is not mechanical but rather in the 16.9344mhz cr02 crystal, connected to pins 71 and 72 of ic2 - saa7341, which stops oscillating, and is easy to detect using an oscilloscope or frequency meter. As it is an SMD component, its removal must be very careful and in its place the crystal code 421230399 must be placed, this being a conventional component but appropriate to the circuit. |