Cce Repair Tips

Search: cce
Results: 4816

Make	Model	Symptom	Problem	Solution
CCE	HPS2904	When turned on, there is loud and sound, but there is no image (plot) and filament access. When moving the screen the image appeared, but it was out of focus and blurred. If you turn it off and on again, it comes back without the plot	100k r916 on open trc board.
CCE	HPS2081D	When turning on the TV, the 47r wire resistor of the bridged diodes burns	Ci str 50103 shorted and the zener diode that is between ground and pin 4 of str 50103 (regulates 103vdc) shorted. with the series lamp still showing a short in the circuit, d405 (by95d) was found to be shorted to pin 2 of the fly. Changed the TV and it worked.
CCE	HPS 1403	After the image appears, it turns on and off	Verificar transistor q802 (bc337)
CCE	HPS2003	Takes 10 to 15 seconds. the image appears	Fly back.
CCE	HPS 1470	It works for a few minutes and drops to number 1 and keeps changing 1-cleared several times until it stops completely and no longer obeys the commands	The defect was the power switch changing to 1m of resistance, it's soft! Sometimes it returned to normal, without any resistance and sometimes it measured high resistance. I left the meter hanging on it and watched the value fluctuate. that was awesome!!!
CCE	HPS14R	Vertical closed almost completely and the horizontal a little, about 5cm on each side	D201(1n4002) bad, killing the 8vcc on pin 10 of the ci tda8361.
CCE	HPS-1480D	Expanded image	The fly ferrite wire inverted "loop". r301 of 2m7 open
CCE	HPS 2071 OU OUTROS	The power supply starts and turns off soon after	Q802 changed. (To find out if the defect is a power supply, do the following	Short circuit the collector with the emitter of q807 “smd” you have to stabilize the power supply at 103v, if this does not happen, the defect is actually in the power supply.
CCE	HPS 2981	Stop and the stand-by LED is on	Damaged flyback
CCE	HPS2081D	The on/off button does not work, it only turns on via the master button. The varicap doesn't work, leaving the blue screen (selector stopped) and thus remaining silent	Dz 813 shorted.
CCE	HPS-1402	Does not tune to all channels	33v zener shorted
CCE	HPS14R	No characters appear	Resolder the ic701 and pin 25,26 and 27 components, check r717 2k2, check the coil around the flyback, it must have 5 turns.
CCE	HPS-2071	Image losing horizontal synchronization only at the top	Replace c404 with 4v7
CCE	HPS-2706	Black line horizontally	R306
CCE	2171	Hoarse sound	Alter r113 to 10r
CCE	2991	50v com 18v	Q409
CCE	HPS-2971	Noise in audio	C671
CCE	HPS2971	Hoarse sound	Alter r113 to 10r
CCE	VCR 90X	Device does not turn on	Display indicating the presence of tape in the compartment, accepts tape normally. This occurs because the video is programmed with a timer. When you eject the tape, you will see a clock symbol appear on the display. procedure: connect the power cable; place a virgin ribbon or one with the seal intact; press the time rec key on the remote control; the video will turn on; press menu...program... and delete them all using the reset button on the remote control;
CCE	VCR 90X	Display completely off or clock after making the adjustment does not change	Procedure: reset the device plug the device into the socket press the power key to turn on the device short circuit momentarily short pin 10 (by) of the ic901 located on the front panel to ground (the device will turn off) turn the device on again by pressing the power key follow the general procedures to adjust the clock.