Cce Repair Tips
Search: cce
Results: 4816
Results: 4816
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS-2780
|
Sem osd | He's gone | ||
| CCE |
HPS-2997FS
|
Turns on, turns off in seconds (cold welding type symptom) | Leaky q802 | ||
| CCE |
HPS-2991FSC
|
Vertical closed | Check q805 and q802 | ||
| CCE |
1403
|
Horizontal intermittent but with audio {dark screen} | Flyback base terminal with cracked circle-shaped solder | Solve terminal | |
| CCE |
HPS2185FS
|
The sound was defective, I changed the sound ci, it turned around | But now the regulator transistor is burning | jose emanuel da silva | |
| CCE |
HPS2071
|
Whistle on standby sound | I changed the str but the defect persisted, I changed r804 to 2k2 defect resolved | orlando batista | |
| CCE |
HPS-2095B
|
No color, no contrast, when changing channels the screen becomes dark. | 12r/2w r-116, altered. | Ronan | |
| CCE |
HPS-2971
|
Turning off after a few minutes for no apparent reason | Q802,q804, q805 (bc337) | Araujo | |
| CCE |
HPS-2971
|
Does not light up. | C409 560kpf | ||
| CCE |
HPS-2991
|
Horizontal closed, dark screen | C409 - 390kp/250v. | Andrade Sequeira | |
| CCE |
HPS-2997-FS/2971C
|
Turns off after 4 hours + or - and turns on again if you press power | R416 (820 r) open, after heating the horizontal deflection sector, television turns off without apparent cause, power supply ok | Replace resistor r416 (820r x 1/8) replace polyester capacitor c-421 (47n) is usually altered | Clovis |
| CCE |
HPS-1495
|
White image | C555 (3,3ufx250v) | ||
| CCE |
HPS2185
|
Serration with side bands | Altered c825 electrolytic | orlando batista | |
| CCE |
HPS2003D
|
Normal sound, no image and no high voltage | Tda 8841 | Juracy | |
| CCE |
2983
|
Turns off after a few seconds | Troque q802,q804,q805 | Turbey | |
| CCE |
HPS2971
|
No sound in the channels, just hiss. | C671 - pino 48 do micro | PROFYSSYONAL | |
| CCE |
HPS2991FSD
HPS2991FS |
There is no image | Check c409 | PRO | |
| CCE |
HPS-1402
|
Only the right LED lights up. | Shqqh | ||
| CCE |
HPS-1407 -2007 -1423 HPS141
|
On televisions that use the ci tda 9570, it can be observed in some cases that the “standy_by” led lights up, but when pressing the power key it goes off, without triggering the horizontal oscillator | 1) replace the resistor r 822 with another 15Ω / 3 w - 2) replace the transistor q 822 with a bd 135 | ||
| CCE |
HPS-2181-2191
|
Unstable vertical timing | In locations with weak signals, vertical synchronization deficiency or image aliasing may be observed. | 1) remove the resistor r 407 (180 kΩ), replacing it with a 470 kΩ trimpot. 2) remove the resistor r 408 (270Ω), replacing it with a 1 kΩ trimpot 3) tune in to a station with a weak signal 4) connect an oscilloscope to pin 41 of the ci la 7685 n 5) observe the video signal, adjusting the two trimpots until obtaining the maximum amplitude of the sync pulse without distortion and without harming other channels. |