Cce Repair Tips
Search: cce
Results: 4816
Results: 4816
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS2997FS
|
TV oscillates, lights the filament but there is no sound and the screen does not light up | Wide capacitor 394 microfarades open | edgarfelix | |
| CCE |
HPS1471
|
TV doesn't turn on, all power supplys are ok, but not even the STBY LED lights up. | The 12,000 mhz micro crystal | All you had to do was replace it and you were good to go!!! | bick_sjs |
| CCE |
HPS2991 FS
|
A scratch on the screen, horizontally closed, gives the impression that the deflector is open. | C409 390kpf 250v, aberto | JOACYR | |
| CCE |
HPS2991 FS
|
Turns on and off in protection mode | Open the skreen and notice the vertical closed, replace d410 if there is no 13v on pin 3 of ci 301 | JOACYR | |
| CCE |
HPS 2997
|
Turn on and off | Q 802 can only put 337 end 25 also change cap.834 | fernandoferreira | |
| CCE |
HPS 2118
|
The flyback was leaking (holey), when it was replaced the TV worked without luminance, normal sound. | C 424 with leak, when changing, everything ok. | Léo, Natal-RN | |
| CCE |
HPS1401
|
Dark screen with no image, normal volume, | Solved was sor r914 registration 22k | R914 register 22k | Jocelio |
| CCE |
HPS-2003C
|
No image and normal sound | Generates high voltage but has no image. | I resoldered the tda8841 and the points that got very hot - easy to identify by the color. not resolved. So, I replaced the flyback and that's it. | Tecvideo |
| CCE |
HPS 1470
|
Insufficient height | Even touching up trimpots and changing capacitors with altered values, it wasn't enough. I checked r312 - 2r2 1w, replaced it and it was ok, accepting adjustments. (obs.resit.it increased only when heated, never when analyzed when cold) | OLIBIO ESTUDIER | |
| CCE |
HPS 1407
|
Symptom kept flashing and didn't turn on, sometimes it turned on without retrace | Badly altered resistor on tube board r 901 | I replaced it and everything was fine | |
| CCE |
HPS2185FS
|
Does not turn on, LED blinks | Tda1571(audio) short | ||
| CCE |
HPS2981C
|
Does not exit service off mode | Change pcf8582e memory, be careful not to use other types of memory | ||
| CCE |
HPS 2080
|
Vertical | 2.7m open resistor r 301 | GILCIMAR | |
| CCE |
HPS2979
|
Bright spot in the center of the trc | Q409 | Antonio-RIO BRANCO-ACRE | |
| CCE |
HPS14RD
|
Image closing on the sides horizontal flashing | Ic 502 tda8361 3y ou 5y | Wellington Eletronica | |
| CCE |
HPS - 1480
|
Does not tune channels | R705 - 12k open | Just replace it and it works great. | Tecnardijf |
| CCE |
HPS2007C
|
Image or on a blue screen with lines as if it were out of horizontal frequency. | When reading the voltage on the horizontal driver collector, even with the TV in stand by, it will not have +b 125v, but another value below, in my case it was 60v, | Replace the c409, it must be on the run, | ars |
| CCE |
HPS 2007
|
Presents horizontal retrace lines that disappear when the screen is adjusted, but the lines instantly return without accepting the screen adjustment on the fly back. | Resistor on the kinescope board - fr 901 (value 33r 2w) open | Substituir fr 901 | João Renato A. Jr |
| CCE |
HPS1470
|
Inoperative, missing +b 103v. | Replaced d810 103v zener, c813, and c306 | mirim | |
| TV CCE |
HPS 2070
|
Does not turn on, 103 v power supply with 4 v | C 808 of 102 1k with leak | To replace | AIRON |