Cce Repair Tips
Search: cce
Results: 4822
Results: 4822
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
HPS14RD
|
Image closing on the sides horizontal flashing | Ic 502 tda8361 3y ou 5y | Wellington Eletronica | |
CCE |
HPS - 1480
|
Does not tune channels | R705 - 12k open | Just replace it and it works great. | Tecnardijf |
CCE |
HPS2007C
|
Image or on a blue screen with lines as if it were out of horizontal frequency. | When reading the voltage on the horizontal driver collector, even with the TV in stand by, it will not have +b 125v, but another value below, in my case it was 60v, | Replace the c409, it must be on the run, | ars |
CCE |
HPS 2007
|
Presents horizontal retrace lines that disappear when the screen is adjusted, but the lines instantly return without accepting the screen adjustment on the fly back. | Resistor on the kinescope board - fr 901 (value 33r 2w) open | Substituir fr 901 | João Renato A. Jr |
CCE |
HPS1470
|
Inoperative, missing +b 103v. | Replaced d810 103v zener, c813, and c306 | mirim | |
TV CCE |
HPS 2070
|
Does not turn on, 103 v power supply with 4 v | C 808 of 102 1k with leak | To replace | AIRON |
CCE |
HPS1471
|
Didn't care | Tube socket, main cause, then we changed the two bc 337 and the two protection system smd | edsom | |
CCE |
HPS2971
|
Has high; lit filament; normal power supplys; but no brightness | Replace c901-1kpf/2kv-(screen) | valter morandini vieira | |
CCE |
HPS-2003D
|
Dark image with bars without contrast and without focus (looking like a bar generator) | Fr403 open and c425 without capacitance (all on the vertical line). | Tecvideo | |
CCE |
HPS1471
|
Horizontal output shorted | Observation, this TV had a shorted horizontal output, I replaced the two bcs, I replaced two protective SMD transistors and nothing, always on the protective eht pin it armed and did not allow the same oscillation until I disconnected all the outputs from the secondary power supply and then I found out that it wasn't a power supply defect, so I disconnected the protection pin and then it didn't turn off, it turned on with an image as if the tube was weak, then I went to the RGB board and removed the socket, I resoldered it and everything was resolved, | edson v | |
CCE |
HPS1402
|
TV doesn't turn on and the stand by LED stays half lit, very low power supply +b. sometimes +b goes up and turns on. | C812 47uf/25v changed | Ricardo Moreno | |
CCE |
HPS 2976
|
In stby. pressing power the voltage in d808 and d812 doubles and in d807 and d811 it drops | C825 sold out | Replace c825 | ivo pavesi |
CCE |
HPS 2976
|
In the league *tea 1507 n oscillate* | Dz 801 short | Replace the dz 801=18v | |
CCE |
HPS 2808
|
Burning vertical output, elevated power supply | Replacing the fly back I put it original | Sr Silvas | |
CCE |
HPS 2090
|
In stand by the power supply is normal, when it fluctuates Hz then the power supply drops to 70 v | Defective deflector coil (yoke) with shorted turns | Rogério | |
CCE |
HPS 2071
|
Decentralized horizontal | Diode d 407 short | Replace diode d 407 which is next to the horizontal drive transformer | Lima de João Pessoa |
CCE |
HPS-2071
|
Blinking LED, won't turn on | Sound output, ci-tda1517 short | Tavinho | |
CCE |
HPS1402B
|
Fly back exhaust, no image | After changing the fly back due to AT leakage, it appeared with a lack of focus, even trying to adjust it | In these cases, check that they work. of ci tda9309, which although it is vertical, when damaged due to fly at exhausts, causes this effect. After being replaced, the TV started working normally again, with stability in focus and screen. | ELETRONICA ESTUDIER |
CCE |
HPS1471
|
Tune, don't tune in with popcorn | Varicap | marco reis | |
CCE |
HPS1471
|
Does not turn on standby LED blinks | Q802 defect | GENIVALDO |