Cce Repair Tips

Search: cce
Results: 4816

Make	Model	Symptom	Problem	Solution	By
CCE	HPS1473	Vertical closed and shutting down	Q 802 bc337	Replace q802 bc337	celitosanto angelo
CCE	HPS1471	It doesn't turn on, or the LED keeps flashing, if you enlarge the screen you can see that the vertical is closed	If the +b and -b of the vertical are ok, check the +b 8v of the q802 may be open		BRUSKE
CCE	MS606	Working --- but no audio --- I didn't find the original schematic	Gradient ms-501 check the amplifier	Replace q303	Alextecnico
CCE	TV-2918USP	Band on the side of the screen and the image is a little shaky	Change not measure c402		ADRIANO
CCE	STILE D42	Doesn't start	F, q3, q1. pci power supply code mlt198tx	After removing q1 in short and replacing f +b5 staby was already present, q3 =f13nk50z by p10nk80zfp and q1 smd by bc556.	BRUSKE
CCE	TV2118USP	Vertical closed and burning fr301	Fake vertical outlet causes fr301 to burn, insert original		beto2828
CCE	HPS1497	Vertical does not open properly 05cm up 05cm down	Deflector	Replace of the same	<small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
CCE	HPS 2071	Symptom: it doesn't turn on when you press the on/off button, the LED just keeps flashing, and it emits noise from the speaker at intervals, which indicates that the TV oscillates and cuts out again! the +b which should have 103 volts has only 77 volts.	Capacitor position c 825 of 47 micro, 160 volts exhausted.	Just replace it and it’s back to normal operation!	Denilson Santos
CCE	HPS 2071	Symptom: it doesn't turn on when you press the on/off button, the LED just keeps flashing, and it emits noise from the speaker at intervals, which indicates that the TV oscillates and cuts out again! the +b which should have 103 volts only has	Capacitor position c 825 of 47 micro, 160 volts exhausted.	Just replace it and it’s back to normal operation!	Denilson Santos
CCé	HPS 2909 NãO MARCA	Crackling high voltage.and no sound	R816 aberts 130k I lifted the q 601 collector and everything was normal	Replace the indicated components	luiz tv som
CCE	TV2918 USP	Completely stopped power supply	Change the power supply ci (cq1265 rt), c517 and 518. Note: I put 47x50 and it turned out great.		reinaldo almeida
CCE	HPS 2991 FS	It turns on the panel or control, but only turns off at the socket. Tsound is no image and the 205 volts are less than 140.	Polyester capacitor position c409 of 390 nanos close to diode d 401 exhausted.	If the symptom is as described, test the capacitor on the capacimeter and you will certainly find it depleted, then replace it and run for the hug!	Denilson Santos
CCE	TV-2118USP	Cushion effect, horizontal black bars	Q 406 e r428	Replace the q406 with the same or equivalent, replace the r428 with 82k gold	Fenixtec
CCE	HPS 2971	It oscillated but did not light the filament. I placed a filament on the outside and saw 3 colored lines in the vd vm az at the top of the screen in a vertical direction. this line is standing. but for those who are confused: horizontal.	An imperceptible crack in the foot of the deflector fitting connector that is connected to the c 407= 3k3/250 blue wire line	01/26/13 flad 8 long river.	Flad 8
CCE	HPS-2981	I'm sound	C-120 -10k shorted	Replace	LUCIANO
CCE	HPS2071	TV didn't tune or auto tune. not manual and sometimes when it turned on tsound was a blue screen, other times it wasn't and the seletronic voltages were normal except for the fact that it had a voltage well below about l v.	After several changes of components in the RF circuit, changing the memory, the chapter was checked. 711 of 33pf cer. leaky disc. .	After changing it, the TV returned to normal	eletronica c.r.
CCE	TVS 2910	Does not turn on led off and power supply pulsing at 140 volts	D808 shorted next to the power supply chopper transformer	Replace	ELETRONICA CARLOS
CCE	MD2200	Radio doesn't work	D108 shorted to 5v1, c156 with 22nf leak	Replace diode and capacitor	orlando lott
CCE	HPS-1471	Led off +b104v 15v and the voltage is 5v with only 1.2v	Q804 is faulty, tsound is no point in testing, you have to change it and the defect will be remedied.	Q804=bc337	samuel leite
CCE	HPS2198AV H-2197A	When turning on the stand-by LED flashes intermittently but does not open the image	Solda fria col e 12v+ do fly-back	Resolder all fly-back terminals and reinforce the solder	gilbertobock