Cce Repair Tips
Search: cce
Results: 4822
Results: 4822
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
CCE |
HPS-2991
|
No current on the screen, or with just a little voltage when you touch the screen potentiometer | Seems to be the bad fly back, or the tube | Check the r-423 is close to the vertical output (1k) | Ademar / Videira sc |
CCE |
HPS2901
|
The LED does not turn on or light up. | Replace the 18 V zener that was leaking. | joosias | |
CCE |
HPS2988
|
Does not turn on, stays on stand-by | Horizontal transistor power low | Replace c 825 de 100μF 160v | MARCIO ALVES |
CCE |
HPS-2197FS
|
Turning off @@@ | I replaced the bc337 and caps. high voltage filter and nothing. the defect was the col pin of the flay cold solder resolders all pins ok | Help yourself leave your tip | ELETRONICA ARNI/L.LEAL-SC |
CCE |
21AVP
|
Does not tune in to any channel | A eprom c 2404 | Replace for another but you have to program it | eletronica pai e fihos |
CCE |
D3201
STILE |
Power supply inoperative - replacing ncp1607b with fan7530 | Ncp1607b hard to find | Replace with fan7530, remove capacitor pin 2, connect 47k resistor to ground on pin 2, connect 47k resistor to pin 2 at the junction of r1 with the return transformer. | Rubens - Videotele |
CCE |
TV2118USP/AV
|
Excess width | Capacitor 409 mur460 shorted | klein | |
CCE |
HPS21 AVP
|
Does not turn on high power supply | Ci tda 1533 bu1508dx tl431 zener 10v | After changing the ci, the bu was shorted, tl431 and the zener were replaced | neweletrotech ctba |
CCE |
HPS-14BSP
|
LED keeps blinking and doesn't turn on | Short sound output | eletronica bianca ipira-ba | |
CCE |
HPS 2991
|
Turns on, turns off when turned on, the screen is white with traces, no sound, no image | R416 820r open next to the flay | Replace | E.MATOS |
CCE |
HPS2007
|
Flashing LED does not turn on | Fr401 1r open, q402 bu2508dx shorted and I resoldered the 401 trafo wire that was broken, it was ok | bob | |
CCE |
HPS-1497
|
Bad beats | D 813 shorted | BETO | |
CCE |
HPS-2007/E
|
Does not work or does not oxidize | Has +b on the horizontal output but does not oxidize | Swap (q-802) bc 337 open | Ademar / Videira s.c |
CCE |
HPS 2185FS
|
Closed 4cm on the sides, then turns off. normal sound and video. | C 825 (47mf/160v) na power supply. | Ademir tc | |
CCE |
HPS2971FSV
|
One more tip for forum colleagues....... all normal power supplys, filament lit, but no image i.e. dark screen, if you open the screen a white screen with retraction lines and sometimes a normal image appears. | Cause: c909 on the crt board (kinescope), (screen capacitor) 1kpf\2kv. change without measuring. | ADHEMAR CAETANO DA SILVA (TECMIL ELETRONICA) NOVA FRIBURGO, RJ | |
CCE |
HPS2185
|
Shorted zener diode d809 (10v) and burning resistor r830 (47r) | Ci tda9570 | Just replace it and that's it. souza electronics | dedley |
CCE |
HPS2971C HPS2983
|
I'm sound | C661 | Barter it | WARLEY CESAR |
CCE |
HPS-2005
|
Works and turns off | Replace q-802 (bc-337) | Ademar / Videira sc | |
CCE |
HPS-2971
|
Sound I am / sound is the audio | Change without testing transistors q-802/803/804 and c-661 | Ademar / Videira sc | |
CCE |
HPS-2981
|
Goes out of tune alone | Remove the aft coil (t-103) remove or break the internal capacitor and place another capacitor of approximately 30 pf below it | Ademar / Videira sc |