Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem	Solution	By
CCE	HPS2185	This TV turned on the LED and when starting it kept hitting the relay.	I found the solution by changing the ic802 (kia431) it works but the filament didn't light up, the led kept blinking, weak trc result.		joosias
CCE	HPS1471	Blinking and not arming	After a lot of time wasted changing the bc 337, power supply capacitors and others.	Discover the 100pf capacitor c 410 shorted	mica
CCE	HPS 2004B	Doesn't start	C423 shorted, kills +b of the supply, 180v line, flay back output, after changing = screen washed = fr901 open, (rgb pci).		Maurílio
CCE	HPS2971 DEBIQUE	Tv with left sidebar r401 18k open and capacitor c 406 shorted	Replace the two components
CCE	HPS2001	Burned by electrical discharge	Burned micro, varicap, sound output and eeprom	When carrying out the test, I verified that the 5v power supply was low, I disconnected the VCC pin from the micro and varicap and the 5v was restored, I replaced the micro after a lot of work to find it, I turned on the TV, which turned on and then turned off, I removed the eeprom and I tested it and found that it was defective, I recorded a new one and the TV turned on, I tuned it and nothing, I put a signal on the AV and the TV showed normal sound, I made the adjustments in service mode, then I remembered that I hadn't soldered the 5vcc pin on the varicap, I soldered it, turned on the TV and nothing, the 5vdc dropped again, then varicap uv1336/f shorted out, I looked in my scrap and found a varicap alps, I checked the pinout and it checked, I put it on, the TV turned on, I tuned it and nothing, I looked for information about adaptation of varicap and I had the information that it was compatible, but its communication protocol was different and I needed to enter the TV's service mode and replace it, I did this and tuned the TV which worked normally, I left the TV in test and after some time the audio was noisy, I put the osciloscope on the audio output and the positive semi-cycle of the audio was being cut off, I tested it at the input and the signal was normal, I replaced the audio output and it was normal, I left the TV under test for a week and everything normal.	ivan@
CCE	HPS-1465E	No image with black screen normal sound, the defect is intermittent, sometimes when hitting the board the image would return.	Cold soldering on ic501 la7680.		This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	2918USP AV	TV with image folded at the top	Ci do vertical ci 30i	Replace the same one for a new one!	adriano SB
CCE	HPS-2070S	Does not have +b 103 volts	R 803 470k open	Replace	JAUCILIO
CCE	HPS2081	Lacks width and no OSD	Rahts	Just replace it and move on to another one.	eletronica vieceli
CCE NOTBOOK	IPL232	Doesn't start. only works with battery	Replace ic u21 8206gn		DEBIQUE
CCE NOT BOOK	IPL 232	Works only on battery	U 21 ci8206gn battery controller	Replace ci
CCE	TVS2118 USP/AV SL23-1	Stretched image and cushion effect	D-410 and d-409 shorted	Replace	LUCIANO
CCE	HPS2971N FSV	Does not turn on, only stand by, normal power supplys	Drive horizontal tf 401 aberto	Changing the horizontal drive, TV ok	jair das cruz eletrônica universal avenida
CCE	TV-29USP	Image flashing, and retrace lines appearing when you turn on the TV	C310 e c311 smd (470pf)	I replaced both with ceramics and everything resolved, it's a good idea to also take a look at the c402 and 406	MARCONDES LIMA,Jaicós-PI- Brasil
CCE	HPS2910	It turned off after about 20 to 30 minutes	After checking the 3 bc 337 from the power supply and capacitors 100/160 and 33/160 and not being successful, I then started working on the line that comes from the micro (col), I checked q 404 and q405, but with no result but after the replace from zd404(zener 4.7),d402.d405(1n4148) the TV stopped turning off	Replace zd 404 and d405 and d 402	JOSÉ GUSMÃO
CCE	MD 3130	Display fraco‎	R520 smd changed		luis carlos [nene]
CCE	HPS 1479P	Black stripe on the left side of the screen	C 417 defective	Replace c 417 and that's it disk capacitor 331 by 2kv	cardomingues
CCE	TV2118	Blinking the +b led with 260v	I changed the IC803 and the TV worked normally, but when I increased the volume the image kept shaking and wanting to close	Replace the 16vx1000μF c831 with a 25vx1000μF one	BETO ELETRONICA ACRELANDIA ACRE
CCE	HPS-2007	Does not turn on or turn on standby, does not oscillate horizontally	Q804 3.3v open		MARCONDES LIMA,Jaicós-PI- Brasil
CCE-TV-LCD-	STILE-D32 000000	Blowing the power supply fuse with no defect in the primary. rectifier bridge, capacitor, and good fet..... defect in the secondary	Q 05 in short and fets q 02 and 03 with leakage. Note tsound is no point in the multimeter measuring good.	Swap the culprits and you're done....	eletrocairuga charqueadas rs