Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH200	Inoperative, only blue volume LED on!	Open smd l4 inductor	Replace l4 for another...	pfa
PHILCO	TPF2121F	The TV only turns on by pressing the power button on the panel, that is, it does not turn on with the control.	Defective sensor, position ir1101 which is on the plate on the front panel of the TV, sensor rpm-693b.	It was replaced for an identical one and it looks great!...	Armando de Olímpia
PHILCO	TP-2052N	Dark screen with no image and with normal sound when the screen increases, a torch appears like an arcuires	Defective vertical output tda8356	Replace	EletroClaudio Aguas Belas
PHILCO	PCM2044	Poor convergence, in the image and characters, and heating up r711	Oxidized deflector coil	Replace deflector	PALAURO
PHILCO	PT	Power supply did not oscillate	Ic do som	Replacement
PHILCO	PCM-2051	Volume increases or decreases every 10 points	Memory defect	Reset the memory: unplugged, press and hold the ch+ and ch- keys on the TV. Turn on the power and wait about 5 seconds until the stand-by LED lights up. release the pressed keys and turn on the TV and reprogram the channels and settings. If the defect returns, replace the memory and perform a reset.	Diego PG-PR
PHILCO	PCS-2976S	Resolder tube board 6 wire mesh	Resolder		SEM IMAGEM TELA AZUL COM RETRAÇO
PHILCO	PCS-2956N	Works for a while and turns off	Weapon protection	I removed the resistor r 932 and it worked normally	noel batista
PHILCO	PH200	Does not turn on as if the power supply has a problem	Remove the tda7265 sound output, if it turns on, replace it	Replace sound output	Cezar
PHILCO	PCM 2051	The TV turns on and off in seconds	R 705 3r3 measuring good to put a jamper		eletronica rodrigo 048 32429465
PHILCO	TP2920	When it turns on, the LED goes off, the tube blinks a few times and goes off, then the LED keeps blinking	Changing capacitors c1701 and c 1703 6n8x1k6v polyester.......it was zero again!!!!		adilson
PHILCO	PH14C	Dark image	BF 422 and 423 leaking, change all BF's on the TRC board		Continental
PHILCO	PCM 1444.2044	No color.	Swap.c.504.	Resolved	hermildon jose t de sousa
PHILCO	TP14U56	When plugged into the socket, the power supply gave a signal that it would work but it didn't, and the LED didn't even light up. and the +b voltage was just 10v and the normal 4.7v voltage	R107 of the LED and e-prom system was open and the sw101 was broken.	I replaced the touch switch on the power sw101 and it turned on but the LED didn't work, I replaced the 100k or107 and the LED came on then it was just a hug.	DIGITEC ELETRONICA (65)9608-4535
PHILCO	PC-1438	Does not turn off via remote control	Q-902	Replace and test.	ELETRONICA NISSEI SOUND embu-sp
PHILCO	TP2053S	TV didn't light anything; power supply did not oscillate, secondary zero	In my case it was the open resistor r911 2,200k		chinês eletronica solânea
PHILCO	PCM-1451	It doesn't turn on via the remote control, but via the panel and then the remote with all normal functions	Believe defect in the main power supply	Replace of capacitors c913 and c911 of 1μF/100v and 100μF/25v respectively.	eletrônica fernandes(to)
PHILCO	TP29C21	When the TV is plugged in, it activates normal stand by, but when you press the power key, the LED goes off as if it were going to work and nothing, only the LED keeps blinking	Lack of -12v voltage on the power supply secondary	D 909a shorted, r 912 and r 910 open. When replacing the TV it worked normally.	Eletronica Som & Imagem
PHILCO	TV PH21SS TV PH21SS	Nâo liga nem led stand by	R520=120k	In my case it was (r520=120k) - it worked 100%	neupsx4
PHILCO	PH 21C	Does not turn on, device inoperative +b only 30v and does not oscillate	3v3 supply failure, diode d872 shorted causing the defect.	Replace 3v9 diode d872	celinvds