☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4811
Make Model Symptom Problem Solution By
PHILCO PC-1444/2044
Severe noise in the sound, normal image C-722 = 470x25 FERNANDO S
PHILCO TP1454
Faulty vertical...horizontal output getting very hot Change the circuit ic601 tda9309.... place a 12r resistor between the base and emitter of the horizontal output transistor FUBULHA-PI
PHILCO PCM1444
CPH05 		Does not open the vertical, good ci, tsound is no 2.8 volts on pin 43 of the ic-501 Check if the r-802 12k resistor is open If said resistor is open, replace it. Paulo Sertel Itararé SP
PHILCO PCM1443
CPH05 		Horizontal K (again) C-709 10nx100v open (no capacity) Replace it with a new one and a hug Paulo Sertel Itararé SP
PHILCO PCM2043
CPH05 		Tsound is sound, tsound is an image but the LED blinks and tsound is no voltage on the protector The r-713 resistor changed (interrupted) Substituir o r-713 100k Paulo Sertel Itararé SP
PHILCO PCM2043
CPH05 		LED flashes (standby) and seconds after switching on C-722 470x16 volts alterado Replace it with a new one, if resolved Paulo Sertel Itararé SP
PHILCO PCM2144
CPH05 		Tremulous image C-205 2.2x50 volts exhausted Replace the c-205 with a new one and readjust the trimpot p-201 10k Paulo Sertel Itararé SP
PHILCO TP14U56
Without image, with osd and sound D602 Replace d602 with leak joaomvjr
PHILCO TP20U56
Without image, with osd and sound D602 Replace d602 with leak joaomvjr
PHILCO PH29C
Blinking LED doesn't work D 810 fr154 macceletronica
PHILCO TPW3280
Tries to turn it on, it starts to activate but it doesn't work, the LED keeps flashing Wide capacitor c708 5n6 macceletronica
PHILCO PCM 2044
Only in stand by does not oscillate Closing a short in the collector and emitter of the q 905 oscillates Changing q904 or even leaving the short may not perform some functions but it works celito santo angelo
PHILCO TP2052N
Turning off immediately after turning on Dz101 3.9v with leak Replace it eletrônicatual [nen]
PHILCO PH 14C
Image erases and switches to one of the colors Transistor bf 423 rgb output eletronicaastec
PHILCO DVD PH155
Doesn't start Defective photocoupler Changing the photocoupler johnny busnadiego
PHILCO TP-1452N
TV with normal sound / with characters / washed black screen, opens the normal retro screen Replace flyback DOIDO DA ANTENA (This email address is being protected from spambots. You need JavaScript enabled to view it.)
PHILCO PCS-2976
Blurry image.totally out of focus. Circuito vertical. Replace. This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO PVT2010
Does not come out on stand-by Saida Horizontal / Saida Vertical / Cop. 541 Replace mentioned items eletronicaapolo
PHILCO TP2053
TV wasn't turned on, it just kept making noises from the speaker like toooooooooooooo I checked everything on it and didn't find anything bad. Then came the surprise: the magnet of the primary power supply transformer was detached, so I glued it back together and it started working again, and the very large transformer that is next to the MOSFET was either loose or detached; This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO TP1454
It just stays on stand by, +b voltage is around 30 volts and it doesn't work D-908 shorted killing the 12 volts from the vertical Replace d-908 samuel leite