Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILCO |
PCM-1451
CPH-06M |
Reduced frame (intermittent), no color in palm. | Ic501 tda8841 faulty | Replace ic501 | Silvio Tur |
PHILCO |
PCS 2976
|
Burning horizontal outlet | Q702 leaking | To replace | niltron |
PHILCO |
PCR 2049
|
Dark screen with sound | C709 | Changing the c 709 tsound is no point in testing it, it is next to the horizontal output | itan ( cabeça) |
PHILCO |
TP1410
|
Does not turn on, just stays on standby and arms and disarms | Cold solder on r931 | EletroClaudio Aguas Belas Pe | |
PHILCO |
TPF 2130
|
TV stopped LED off relay does not arm and power supplys pulsing with all values below the specified | Check r927, photo coupler, ic 903, c 925 some of it was possibly faulty in my case the pro was on c925 and r 927 I changed it and ran to hug | Roberto Consertos | |
PHILCO |
PCS 2952
|
Turns on and protects goes to stand by | Capacitors c 711 e 712 altered | Debique | |
PHILCO |
TP 14/2054
|
Sometimes it doesn't turn on as if the on/off switch is faulty | R 919 of 120k with changed value | Replace r 919 | NILTRON |
PHILCO |
PCM 2044
|
Turning off (when changing channels) | Zds03 | Edilson | |
PHILCO |
PT 1453
|
Takes time to switch channels and flashes | I wanted to know how yesterday I could work I'm lost | laercio d costa | |
PHILCO |
TP 2941
|
Turns on and then turns off and the LED flashes orange | Zener dz 401 with leakage, optional you can use a 24v one | Master Eletronica | |
PHILCO |
TP-1452N
|
Stays on standby, does not turn on, high +b voltage (135volts) | Replace capacitors 911 and 913. | Valmir | |
PHILCO |
PH4OO
|
Does not turn on, noisy power supply (tick tick tick) | EC28 Capacitor Power (1000x16V) | Replace coil l4 (smd) on the positive of the ec28 | cesar_unitec |
PHILCO |
TPF 2940
|
Burning 100r resistor (1703) on the demag pci. | Cm 1701 connection without contact with wires | Remove the wires and adjust the connectors attached to the wire | cesar_unitec |
PHILCO |
TP 1453
|
It turned on normally but tsound was no video in any way, not even accelerating the screen on flay back, RGB voltage all normal | Socket, just change it, the bastard has a short | fabiusmax | |
PHILCO |
TV 14 C
|
TV with greenish color with vertical stripes | Burning of resistors and transistors on the kinescope board | Replace o resistor r 928=a 220ohs,r926=220ohs;transistor bf 422 na posiçao u922e bf423, na posiçao u923 | moroni eletronica |
PHILCO |
TPF29S4F
|
Doesn't start | Capacitor 733 - 22mf/250v | tyko | |
PHILCO |
TP 1410
|
TV arms the power supply has all the power supply voltages, arms the relay then disarms and the LED keeps flashing | Horizontal drive, cold welding on q702 and t702, observation the 9 volt voltage of the IC 905 regulator only appears with the power supply armed, on stand b tsound is no this voltage and +b is around 80 volts | Resoldar t702 e q702 | Ricardo Alves/ Eletrônica do Ricardo Caeté |
PHILCO |
TPF 2140
|
Intermittent power supply | Sometimes it doesn't give stby | Capacitor c936 com fuga | carlos |
PHILCO |
PH 21C
|
Comes with normal colors after a certain time it turns purple | Defect in amplifier transistors | This TV required a lot of work because the image was normal and then turned purple, first I replaced the transistors on the tube board, I thought I had solved it, but it came back under warranty so I decided to replace the amplifier transistors on the board and to my delight tsound was no more defect. the image would flash purple. | fernando timbauba PE |
PHILCO |
PCS 2976
|
TV turns on and off, turns on the screen, closing the horizontal in the shape of panties, like it had a bad deflector coil, high power supply 140 vc | R919 changed, it is a precision resistor and its value is 120k | Replace the resistor | Ricardo Alves/ Eletrônica do Ricardo Caeté MG |