☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4775
Make Model Symptom Problem Solution By
PHILCO TP20V56
CP02R0 		Doesn't start D909 in the power supply secondary luiz g.silva
PHILCO TP20V56
CP02R0 		Doesn't start Power supply secondary d900 luiz g.silva
PHILCO PCM2044
Verticalopen only 5cm from the middle upwards C-613 pin 3 of vert output. 2n2 was with 1n6 joaoxx
PHILCO TP-2052N
Does not turn on, LED off, device inoperative without voltage on the power supply secondary. Cold welding at the power supply. Resolder r910, r909, d906 and points on the same power supply line. celinvds
PHILCO TP1410
Standby is on but when I turn it on it starts blinking but doesn't oscillate the TV only has +b 106 volts 15 homs resistor burnt or with raw solder check it position r931 and it feeds the 1000mf x 16 volt capacitor take advantage and change it without testing the c918
PHILCO TFP2902
Horizontal shifted right side Capacitor c732 smd 2n2
PHILCO PCM 2044
05 		Vertical closed dark strip at the bottom Capacitor 1000uf35v no esquema c610 I replaced it, it was a jewel dgspeg
PHILCO PCM2044
05 		Vertical closed dark strip at the bottom Capacitor 1000uf35v I replaced it, it was a jewel dgspeg
PHILCO PCS-2956
CPO1LR01 		TV with no image and no sound; with line of retraces. Irregularities in the ic101 (m37274ma), memory, blocked the system when activating the image adjustment in the menu. After replacing the ic 101 (m37274ma), the device was ok. clayton
TV PHILCO PCM 2044
Blinking led Takes about 20 minutes to work Solution capacitor c722 470μFx25v, replaced and resolved. BF.COLATINO
TV PHILCO 20V56
With drizzle. None of the channels worked, before condemning the seletronic I checked that it had 33v and the appropriate voltages, but when checking the date and clock line I saw that tsound was no clock signal. Following the seletronic backwards I saw that r202 100r smd version was open. because tsound was a sign on one side and not on the other. I replaced it and that's it. all channels are working again BF.COLATINO
TV PHILCO PCM-2046
Doesn't start After finding that the c716, r706 were broken and replaced I checked that the flayback was shorted and I replaced the components and everything went back to normal. BF.COLATINO
TV PHILCO 2956 N
Entering protection resolved The problem with the TV was the wide capacitor (c 728-3u3 1k6) Replaced and resolved. BF.COLATINO
PHILCO PCM 2044
Turns on and off without stopping R115 open and c718 shorted. These two components are part of the 180v power supply. BF.COLATINO
PHILCO PCS-2976S
Reduced frame on the sides, stretched vertical, strange characters and could not access service mode. 24c04 smd memory Memory replacement Evandro Bobsin cardoso
PHILCO TP2054
Image playing beautiful and off I thought it was flye bek, but it was the 6n8 715 capacitor, I just had to change it jcosme
PHILCO TP2053
21 		Stop had no main power supply Ic 901 q 901 tda16846 short, just change it, it works, it works fine negodrama
PHILCO TP20V56
Inoperative, tsound is only voltage on the primary power supply Change power supply oscillator ci tda16846 p ic901 This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI
PHILCO PT1410
Turning off and flashing stand by Change 1000/16v supply capacitor This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI
PHILCO TC-29A11
Does not turn on, without 9v power. D602 in all devices submitted to authorized service, replace diode d602 with a jumper. If this diode opens, the device becomes inoperative. Thank you for this tip as I was already getting nervous about this defect ca.gilberto