Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
PHILCO	TP-2052	Dead power supply	Replace capacitor smd c936 na power supply		fabiusmax
PHILCO	PH21C	Doesn't start	Power supply does not have 95 volts, only 30 volts and the LED flashes intermittently.	I replaced the q815(2sk3115)replaced it with the 2sk2740, ic801(tea1533p)this is not the smd(tea1533at) and has only 8 pins replaced it with the tea1507p, ic803(tl431) and ic802(hpc922-c) this is the photocoupler.	eletronica fernandes
PHILCO	PT-1454	TV only on video and with maximum volume	Microprocessor	Replace the epron and micro if the touch switches are not shorted	This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI
PHILCO HITACHI	PC1605 CPH02	Tsound is drizzle, sound from the carrier and no video.	Q202 leak between emitter and collector.	Replace q202 (bc548a0	Ademir TC
TV PHILCO	PC-1445 CH05	This TV arrived inoperative, without mat, after exchanging the flyback b32-2453-001, it generated, but with a lot of brightness and return lines.	I tested the 180v voltage of the rgb it was 0v, causing the r715-0.47r to be open, after the replacement I adjusted the scrin and focus and as the saying goes "it was just a matter of running for the hug". hehehe.		BF.COLATINO
PHILCO	PCM2046 CPH-5	Does not turn on, or makes noise and turns off and on again	Capacitor c722	C722 capacitor replaced	johnny busnadiego
PHILCO	TPF 2130	Sometimes the TV doesn't turn on, it just stays on standby, similar to a defect with poor contact	1000uf/16v electrolytic capacitor c918, which filters the 12v supply, with little capacitance or high esr	Replace capacitor	AFONSO SANTANA
PHILCO	TPF 2140	When you turn on the power on switch, tsound is a noise in the speaker and the TV does not turn on.	Shorted vertical -12v rectifier diode d909a	Replace diode	AFONSO SANTANA
PHILCO	TP2921	With a chirp at the power supply	Micronas	This TV came into the workshop with the following problem, all the power supplys were low and it didn't light up, so I released the IC 805 and then I noticed that the power supplys normalized. Conclusion I replaced the microwave and the TV worked normally	zezinho
PHILCO	TP29C21	It turned on and at the same time it turned off, remaining on standby	D908 and d908 (cold welding)	Redo the weld	jvb
PHILCO	TFP2940	Turns on, protects and the LED blinks	Replace c 1701 and c1703 5n6?1k6 and adjust screen		Antonio Martis
PHILCO	TP2000		C715 swap		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP2054	Normal power supplys, when turned on it works for + or - 5 seconds, and goes into protection, (the panel LED keeps flashing)	C718 swap		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP 1454	Vertical bar on the left side of the screen approximately 3cm	Change capacitor smd c 705 2n2 pin 16 of the micro does not measure can be replaced with a common ceramic	Replace c705 2n2	fabiusmax
TV PHILCO	TPF2121	Only on stand by, with noise at the power supply.	Q901 faulty and d908 shorted.		edsomvideo
PHILCO	TP1452N	Fountain sobbing	C911 e c913	Replace both if it continues, replace ic 901	Elias2305
PHILCO	TP1452N	With colorful stripes across the screen	R708 (I replaced the vertical output, micro, tda) and it was just low voltage....	Replace without testing..	Elias2305
PHILCO	TP29C21	Charging power supply capacitor, power supply does not oscillate	D915 from primary power supply		This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI
TV PHILCO	PCS2956	Tv philco pcs2956 that the image is normal, but tsound is a strong noise in the sound of the channels as if it had an unadjusted aft coil.	I replaced the ic501 tda8843 2y then it was amazing.		bf.colatino
PHILCO	2049	When turning on, only the channel number (OSD) appears, increasing the screen the image appears, but the next day it is the same thing	Resolder all smd resistors on the tube board.		HP ELETRONICA