Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
TV PHILCO	1454	Then leave and don't care	R910 and r912 open, check diode minus 12 volts was shorted		BF.COLATINO
TV PHILCO	20V56	Drizzle.no channels work	I had 33v and the necessary voltages, but when I checked the date and clock line with the scop (oscilloscope) I saw that tsound was no clock signal.	R202 100r smd version was open.	BF.COLATINO
TV PHILCO	PC 1446	Works normally but keeps flipping channels	Just wash the processor with theener and the processor is back to normal.		BF.COLATINO
PHILCO	TP2052	+b pressing led off	Capacitor as low capacitance	Replace the 1 μF capacitor c 913 that is in the primary power supply TV ok. good luck	george pontes
PHILCO	PH 21C	Closing vertically at the top and bottom	C401- 882j 100	Barter it	This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI
PHILCO	TPF29S4F	TV arrived at the inoperative workshop. I found a diode on the yoke board with a short in position d1701, I replaced it with a new one, the TV started working again, but the screen had stretched corners, I tested the entire yoke board but everything was ok, I went into the service menu and more. it was a defect; Luckily, another TC Philco model TP2920 arrived which had the same chassis, so I ordered the yoke plate and put it in, it was still defective; So, look at the other board, tsound were two wires coming from the 706 capacitor position going out to the yoke board, so I did it from the other board; negative position of the capacitor n pin 2 of the cm 1307 positive n pin 1, then also change the resistor n position r 1702 to 47k then just joy ;8817	Missing wire that connects the yoke with the position d c 706	Remove capacitor c706 put two wires in its place connect socket cm 1703 which is n yoke + a 47k resistor	marcos melo cascavel ceara
PHILCO	TVPH21SS	Doesn't start, doesn't have +b.	R520 of 120k open at power supply.	It was just a matter of changing it and it was ok.	FRANCISCO - ELETRONICA SÃO FRANCISCO This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILCO	TP2920	Turns on then goes into protection, LED flashes.	Replace c1701 and c1703
PHILCO	PC2041	Turning off after flyback replacement	Resistor r723 (27k) open abl line		ARAUJO
PHILCO	TP2052	It doesn't turn on, or it oscillates and turns off and the LED keeps flashing	C706 6n8 leaking capacitor	I put another one it worked perfectly	FRANCISCO RS
PHILCO	TP2053N	Blinking LED doesn't turn on	Shorted deflector coil	Replace the coil	francisco rs
PHILCO	PC2013U CPH02	Vertical closed	Capacitotor c 611 de 100uf/100v rim	Also replace c607 at 10μF/63v and c609 at 4.7μF/63v	francisco rs
PHILCO	PCM2146	Inoperative, stand-by LED flashes and does not turn on	Capacitor c905, replace as it is open		claudio e reinaldo
PHILCO	TP-2054 = TP-2053	It doesn't turn on when the standby LED starts blinking +b at 109v it drops to 15v @@@	Saida vertical tda9309 tv tp-2053 a tv tp-2054 vertical tda9302 a ou h	Help yourself, leave your tip ass.arni	ELETRONICA ARNI-LEOBERTO LEAL-SC
PHILCO	TP-2054 = TP-2053	Does not turn on when turned on, the standby LED flashes	D09, R10=47.0, R12=47.0		ELETRONICA ARNI-LEOBERTO LEAL-SC
PHILCO	TP-2054	E.a doesn't turn on LED keeps flashing @@@@	D09, R10=47.0, R12=47.0	Help yourself, leave your tip ass.arni	ELETRONICA ARNI-LEOBERTO LEAL-SC
PHILCO	TP20V56 CP02R0	Doesn't start	D909 in the power supply secondary		luiz g.silva
PHILCO	TP20V56 CP02R0	Doesn't start	Power supply secondary d900		luiz g.silva
PHILCO	PCM2044	Verticalopen only 5cm from the middle upwards	C-613 pin 3 of vert output. 2n2 was with 1n6		joaoxx
PHILCO	TP-2052N	Does not turn on, LED off, device inoperative without voltage on the power supply secondary.	Cold welding at the power supply.	Resolder r910, r909, d906 and points on the same power supply line.	celinvds