Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TPF2121
55 02 F 6949 020 |
Burning ts horizontal | I can't even watch it, it's already burning | antonio | |
| PHILCO |
PCS 2976
|
When turning on the flayback it makes a leaking noise and then turns off | C715 = 8n2 | Replace without testing | Danieleletronica |
| PHILCO |
PC-1443
|
Bad or distorted image like an old model that has to adjust the horizontal @@@ | Adjust coil LR201, if that doesn't work, check c205=2.2uf/50v, c905=220uf/400v | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
| PHILCO |
PCM 2046
|
Dark image | R717 open | I replaced it back to normal image | carlos w |
| PHILCO |
PCM-1451
CPH-06M |
Reduced frame (intermittent), no color in palm. | Ic501 tda8841 faulty | Replace ic501 | Silvio Tur |
| PHILCO |
PCS 2976
|
Burning horizontal outlet | Q702 leaking | To replace | niltron |
| PHILCO |
PCR 2049
|
Dark screen with sound | C709 | Changing the c 709 tsound is no point in testing it, it is next to the horizontal output | itan ( cabeça) |
| PHILCO |
TP1410
|
Does not turn on, just stays on standby and arms and disarms | Cold solder on r931 | EletroClaudio Aguas Belas Pe | |
| PHILCO |
TPF 2130
|
TV stopped LED off relay does not arm and power supplys pulsing with all values below the specified | Check r927, photo coupler, ic 903, c 925 some of it was possibly faulty in my case the pro was on c925 and r 927 I changed it and ran to hug | Roberto Consertos | |
| PHILCO |
PCS 2952
|
Turns on and protects goes to stand by | Capacitors c 711 e 712 altered | Debique | |
| PHILCO |
TP 14/2054
|
Sometimes it doesn't turn on as if the on/off switch is faulty | R 919 of 120k with changed value | Replace r 919 | NILTRON |
| PHILCO |
PCM 2044
|
Turning off (when changing channels) | Zds03 | Edilson | |
| PHILCO |
PT 1453
|
Takes time to switch channels and flashes | I wanted to know how yesterday I could work I'm lost | laercio d costa | |
| PHILCO |
TP 2941
|
Turns on and then turns off and the LED flashes orange | Zener dz 401 with leakage, optional you can use a 24v one | Master Eletronica | |
| PHILCO |
TP-1452N
|
Stays on standby, does not turn on, high +b voltage (135volts) | Replace capacitors 911 and 913. | Valmir | |
| PHILCO |
PH4OO
|
Does not turn on, noisy power supply (tick tick tick) | EC28 Capacitor Power (1000x16V) | Replace coil l4 (smd) on the positive of the ec28 | cesar_unitec |
| PHILCO |
TPF 2940
|
Burning 100r resistor (1703) on the demag pci. | Cm 1701 connection without contact with wires | Remove the wires and adjust the connectors attached to the wire | cesar_unitec |
| PHILCO |
TP 1453
|
It turned on normally but tsound was no video in any way, not even accelerating the screen on flay back, RGB voltage all normal | Socket, just change it, the bastard has a short | fabiusmax | |
| PHILCO |
TV 14 C
|
TV with greenish color with vertical stripes | Burning of resistors and transistors on the kinescope board | Replace o resistor r 928=a 220ohs,r926=220ohs;transistor bf 422 na posiçao u922e bf423, na posiçao u923 | moroni eletronica |
| PHILCO |
TPF29S4F
|
Doesn't start | Capacitor 733 - 22mf/250v | tyko |