Philco Repair Tips
Search: philco
Results: 4838
Results: 4838
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PC1444
CPH05 |
Image shaking, synchronization and missing color | Change cap 205. exhausted 2.2mf 50v | josé carlos | |
| PHILCO |
TP-2052N
|
TV asking for password, in my case it asked for password on channel 3. | Reset to memory. | Press the channel + and channel - keys and plug in for 15 seconds. | |
| PHILCO |
TP-1454
|
Doesn't start | D-909 opened d-908 changed | GBS.Eletrônica | |
| PHILCO |
TP-1454
|
Doesn't start | D-909 amended | GBS.Eletrônica | |
| PHILCO |
PCM1444
|
Does not respond to keyboard commands | Cause:r713 (changed or opened) | Replace and resolve | jarbas santos |
| PHILCO |
TP2920
|
Turns on, no image appears, and then turns off, goes into protection | Check +b 50v from the vertical ci should have around 42v on pin 3 vertical ci, if it is below this ci value defective. | Bruske | |
| PHILCO |
PH21B
|
Turn on the TV perfect image after a few minutes the image starts to lose its brightness due to this defect | In the abl but it is not, defect in the kinescope board transistor bf 423 with emitter collector leak | Replace transistor v 903 bf 423 | fernando timbauba PE |
| PHILCO |
PCM2044
|
It doesn't have 95 volts | C911 220mfx160vols reset | juci | |
| PHILCO |
TP-2921
|
Excess green color | Eprom reprogramming. and a correction: to enter the service mode of this TV, press menu on the control and on the panel at the same time and wait a few seconds. | FERNANDO | |
| PHILCO |
PCS2952
|
Vertical closed | Ic601-la7833/c610-100/63v/d703 e r720-1r | Replace mentioned items | eletronicaapolo |
| PHILCO |
TPF 2130 REAL FLAT
|
My TV had the LED on when I pressed the power button and it went into standby mode | I replaced IC 601 (STV 9302 a) and resoldered the 936 resistor which was with capacitor glue | TV operating normally, I want to thank everyone for the tip and good luck | Jorge Luiz |
| PHILCO |
TRANSGLOBE B 481
|
Low volume and noisy on all tracks | Transistor t 406 pb 6015 after changing all the electrolytics in the amplifier, and losing some cable wires, I took it out and tested it and it said it was good, I decided to change it, damn the old radio came back to life | Marcio | |
| PHILCO |
TP2054
|
Sound just squeaks like failing, | Replace o capacitor c402 smd | Resolved | |
| PHILCO |
PCM2046
|
Blinking led | Defect l701 open | jglopes | |
| PHILCO |
TP-2054
|
Dull | Capacitor c727 shorted | Replace the 100n capacitor c727 with 100v | somprimos eletronica |
| PHILCO |
PCS 2956
|
Doesn't start | Q 706 or q 707 | ITAN,PARELHAS RIO DE JANEIRO | |
| PHILCO |
PCS 2956
|
Low sound | Ci tda 8843 pin 15 shorted | Replace tda8843 | ITAN,PARELHAS ,RIO DE JANEIRO |
| PHILCO |
PCM2051
|
Turns on works normally, but when turned off it doesn't turn on again | C708 and c709 and to avoid return, replace c704 and c706 | José gusmão | |
| PHILCO |
2046
PCM |
Image comes and goes, standby blinking | R 713 open | Replace resistor with a new one | luiztvsom |
| PHILCO |
PCM2046
|
When it heats up it keeps turning on and off | Resistor 713 changed 100k | julio itaguai |