Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TP 2052N
|
Does not tune channels or poor tuning | Cristal mf 201 | Manoel | |
| PHILCO |
PC 20R38
|
Screen with retrace, no brightness or contrast | C301 0.47yf/35v close to ci oscillator | AdrianChapadão | |
| PHILCO |
PCM-2051
|
LED blinking and power supply oscillating | Capacitor c913 1uf | pardalzito | |
| TV PHILCO 29 |
TPF-2902 E OUTRAS TVS
|
No image (brightness), normal sound, with high voltage, trc filament lights up and normal voltages on the rgb. | Oxidized tube connector, remove and replace the tube plate and it's shiny! | Clean the TRC terminals, spray with WD40, remove the TRC plate several times or if it doesn't look good, replace the connector! | Dreamshacker |
| PHILCO |
TPF 2130
|
It turns on but when the relay goes off it turns off and stays on standby flashing | Replace o ic 601 (stv 9302a | allanaeletronico | |
| PHILCO |
PC-2035
CPH-03 |
Horizontal synchronism | C 613 with leak | To replace | Alvaro |
| PHILCO |
TP 2921
GRS |
Power supply +b 130 +b 10 +b36 only the +b 6.5v does not work | Micronas vtc 4942 | Replace micronas along with the eeprom obs. Heat the 35 watt soldering iron and unplug it to carry out the welding ok | luiztvsom |
| PHILCO |
TP 2021
GRS |
130v power supply at 0 volts | 330 k resistor r 509 open | Replace r 509 smd I replaced it and it worked fine | luiztvsom |
| PHILCO |
TP1454
**** |
The LED turns on and when you turn on the TV it turns off. | Does not start | Was replaced r-715 =3k3 was cut. | Armando |
| PHILCO |
PCM 1443 EMOTION
|
Everything works normally, but if you turn it off and turn it on at the same time, it no longer turns on and the +b stays normal. | R 908 open | Daniel | |
| PHILCO |
TP 2054
.... |
Tv doesn't work | Short circuit | Disk capacitor position = c959 shorted | Armando |
| TV PHILCO |
PCS 2976
|
Horizontal dark stripe | C 705 with amended | I replaced it with another one I thought it could be service mode | kizeuu |
| PHILCO |
2054
|
Power supply inoperative fuse ok | R909 390k | Roberto Consertos | |
| PHILCO |
2976
|
TV stays on stand by and when you press power the LED turns off and then lights up again | Replace fly back | Roberto Consertos | |
| PHILCO |
2976
|
TV works normally but with a horizontal bar on the left side | Replace capacitor smd c705 no pino 16 do micro | Roberto Consertos | |
| PHILCO |
TP1453
|
Turn it on and heat it up r917 | Intermittent | Replace coupler photo | Schulz |
| PHILCO |
PCM-2046
|
Sem 5v no micro,led stand by apagado | Dz904 (30v) e r923(1r 3w) aberto | Replace the two | beto2828 |
| PHILCO |
PCM 2046
|
Reduced frame in four corners | Power supply all ok, micro, oscillator, vertical everything you can imagine | Direct fly back replace | Neguinho(itapevi) SAE-TAV ELETRONICA |
| PHILCO |
PCM-2046
|
The TV was turning on and off quickly without stopping. | Change all the power supply capacitors and also close to the flay back (the electrolytics | Because the low microfraids of both causes the power supply to trip | |
| PHILCO |
TP 1554
|
Vertical does not stabilize and cuts image at the top, change | Change the two power supply capacitors: c914 and c 918 which filters the -12v and +12v. Don't test, change soon. | caio |